Web Mountain Technologies RUC-01 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 100

Web Mountain Technologies RUC-01 Скачать руководство пользователя страница 7

Web Mountain Technologies

Page 1

Chapter 1

Introduction

RUC Overview

Congratulations on your purchase of the Web Mountain Technologies Remote
Universal Controller (RUC).  We appreciate you choosing the RUC to provide
your home / office with a rich set of communications / control capabilities.

The Web Mountain Technologies Remote Universal Controller (RUC) is intended
to be used as a network appliance for the control of a home automation network.
Control signals can be sent over Ethernet, either remotely over the Internet or on
a local network.  One example of such use are commands sent over the Internet
that are then converted into serial commands that are sent to an externally
connected WMT SPIM UPB powerline Interface module for transmission onto the
local powerline.

In addition, the unit contains a second serial port, which allows for the
conversion of one automation protocol to other home automation protocols, such
as Zwave, Insteon, or the ESI drapery control system.

RUC Basic

The RUC Basic unit (RUC-01) provides a basic feature set:
-

One Ethernet 10 / 100 Mb/s RJ-45 interface

-

Two Serial interfaces (DB9 connectors) – COM 1 & 2

-

One power jack

-

Internal webserver

-

Internal Flash and RAM memory

RUC Wireless

Future

RUC Plus

Future

«
...
5
6
7
8
9
...
»

Содержание RUC-01





































































































Отзывы:

Нет отзывов