Web Mountain Technologies RUC-01 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 100

Web Mountain Technologies RUC-01 Скачать руководство пользователя страница 34

Web Mountain Technologies

Page 28

Triggers

This page allows the user to setup simple IF – THEN actions based upon
receiving a particular command, serial string, time of day, or other events. Some
examples would be IF <UPB received> THEN send another UPB command with
or without a delay, or IF <UPB received> THEN send an email.

In addition, the user can setup a Scheduled event from this page or cause a
received signal from one protocol to trigger sending a command to another
protocol. This is also how you setup Buttons for the embedded Control Panel.

NOTE:

IF-THEN type UPB Triggers will not function if there is a Remote session

(using UPStart or some other remote access software) in progress. Scheduled
events will function at all times, even if a Remote session is in progress.

NOTE:

The trigger signal must not come from the RUC – the RUC cannot listen

to itself, and will not see any signal generated by itself. So, the source of the
trigger command cannot be the RUC.

«
...
32
33
34
35
36
...
»

Содержание RUC-01





































































































Отзывы:

Нет отзывов