Weatherford SLS Baseline 9000 FID Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 36

background image

Page

16

of

36

SLS Baseline 9000 FID Total Gas Detector Manual

7)

Wait until the current pressure counts are equal to or close to the target pressure counts,
minimum 2 minutes.

Figure 16: Air Flow Press Cnts

8)

Measure the flow out of the detector vent on the back panel and compare

the measured value

with the target flow shown on the display. If necessary, use the ← key and the numeric keypad
to change the target pressure counts. Use the → key to update the new value. Wait for the

pressure counts to stabilize, at least 1 minute, and re-measure the flow at the detector vent.
Repeat until the measured flow is equal to the target flow ±2 cc/min.

Figure 17: Air Flow Value

«
...
15
16
17
18
19
...
»

Содержание SLS Baseline 9000 FID





































Отзывы:

Нет отзывов

Похожие инструкции для SLS Baseline 9000 FID

Бренд: Gas Clip Technologies Страницы: 2

Бренд: Medem Страницы: 9

Бренд: Atest Gaz Страницы: 24

Бренд: Jaric Design Страницы: 34

Бренд: BONANZA Страницы: 13

Бренд: K40 Страницы: 2

Бренд: K40 Страницы: 2

Бренд: Uniden Страницы: 28

Бренд: Xintex Страницы: 9

Бренд: Geca Страницы: 4

Бренд: Garrett Страницы: 20

Бренд: sauermann Страницы: 144

Бренд: Stinger Страницы: 20

GOLD STINGER X5

Бренд: Stinger Страницы: 37

Бренд: LOCK Inspection Sytems LTD Страницы: 47

Бренд: Lock Inspection Systems Страницы: 61

Бренд: Delta Страницы: 20

Бренд: AKA Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды