WeatherBug UM24 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 29

background image

HD MotionCam

Installation Manual

EN.PM.UM24 20160211

-16-

Page 16 of 29

Utilization of the pan/tilt/zoom functionalities of the HD MotionCam is possible
through the page pictured above.

Captured Images

In order to obtain captured images Port 21 TCP outbound must be open for FTP o
and WeatherBug Technical Support must be contacted at (800) 624-4205 or email
[email protected]. The camera must be enabled through headquarters
in order for captured images to be available through the WeatherBug website.
Once the camera is enabled, using a web browser on a computer connected to a
Local Area Network (LAN), images can be viewed from the camera by visiting
http://weather.weatherbug.com and searching for the location name.

Now that captured images and live video are visible from the HD MotionCam and
available on the network, the rest of the installation may be completed.

«
...
14
15
16
17
18
...
»

Содержание UM24






























Отзывы:

Нет отзывов

Похожие инструкции для UM24

Бренд: Panasonic Страницы: 124

Бренд: Canon Страницы: 43

Бренд: DAITEM Страницы: 22

Бренд: CP Electronics Страницы: 12

Бренд: CP Electronics Страницы: 4

IPC-PDB4830-B360

Бренд: Dahua Technology Страницы: 21

Бренд: Jesmay Electronics Страницы: 6

NG-IPCAMEV8180A

Бренд: Net Generation Страницы: 33

Бренд: Lorex Страницы: 2

Бренд: NEO Страницы: 40

Бренд: D-MAX Страницы: 48

Бренд: Vicon Страницы: 4

RF-Panic-One-Button-319-NN

Бренд: Maxouttech Страницы: 3

Бренд: Idis Страницы: 37

Бренд: HIKVISION Страницы: 12

Бренд: Lorex Страницы: 2

Бренд: Interlogix Страницы: 4

Бренд: M-system Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды