Wayne SWS50-8.5FX Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 15

Wayne SWS50-8.5FX Скачать руководство пользователя страница 4

Operating Instructions and Parts Manual

4

www.waynepumps.com

S

tep

1:

NOTE: Remove pump from stabilizing mount,
used for shipping and packing.
With motor end of pump facing the “outlet /
inlet” end of the tank, mount pump to tank
with the provided carriage bolts, nuts and
washers as shown (right).
For easy installation, install bolts through
bottom.
The bolts can be entered in any slot
to secure the pump providing they are
positioned diagonally from one another.
NOTE: Pump CAN move slightly, even after

bolts are placed. This provides flexibility when

installing into plumbing.

WASHER

HEX NUT

CARRIAGE

BOLTS

WASHER

HEX
NUT

MOTOR END

TANK OUTLET/INLET

S

tep

2:

Wrap ALL external pipe threads with
plumbers seal tape or other thread
sealant.

NOTE: Start tape about two threads

from bottom of fitting. Wrap tape 2 or

3 turns in the direction of the threads

overlapping each turn. Smooth tape

over threads to make sure there are no

bubbles or loose pieces of tape.

HOSE BARB

PIPE NIPPLE

(THREAD BOTH ENDS)

S

tep

3:

Looking at the pump from the motor
end, screw pipe nipple into the
pump discharge located on the left.
All connections will be fully tightened
in steps 7 & 8.

PIPE NIPPLE

MOTOR END

S

tep

4:

Screw straight hose-barb into pipe tee.
All connections will be fully tightened in
steps 7 & 8.

TEE
FITTING

STRAIGHT
HOSE-BARB

TANK

OUTLET/INLET

«
...
2
3
4
5
6
...
»

Содержание SWS50-8.5FX
















Отзывы:

Нет отзывов