manualshive.com logo in svg

Wayne SWS50-8.5FX, Инструкция по эксплуатации и каталог запасных частей, Страница: 10 / 15

Поделиться
Скачать
Wayne SWS50-8.5FX Скачать руководство пользователя страница 10

Operating Instructions and Parts Manual

10

www.waynepumps.com

Figure 6- Vertical Tank

AIR VOLUME

AIR VOLUME

HOSE COUPLING

OUTLET

LUBRICATION

The bearings used in the pumps are lifetime lubricated at the 

factory and require no additional lubrication.

PRECHARGED TANK

Some air is lost through the bladder in any tank. To prevent tank 

failure, check the tank precharge on a yearly basis.
1.   Disconnect power to the pump, so water does not refill the 

precharged tank.

2.   Open a faucet nearest to the tank and allow all water to drain 

from the tank, then close.

3.   Measure the tank precharge at the valve stem using a tire 

gauge.

4.   If necessary, adjust the precharge with an air pump 28 - 30 psi 

on the pump.

5. Reconnect power to the pump.

DISCHARGE

NOZZLE CLEAN 

OUT

PRIME PLUG

28-30 PSI 1/2 HP

DRAIN FITTING

Figure 7 - Precharged Storage Tank

KITS SECTION

REMOVING OLD SHAFT SEAL 

Disconnect power and release all 

pressure from the system before attempting to install, service, relocate or 

perform any maintenance.

1.   Disconnect power to the pump.

2.   Open a faucet nearest to the tank and allow all water to drain 

form the tank, then close.

3.   Remove the four cap screws holding the pump housing (volute) 

to the motor (Figure 8).

4.   Separate the pump housing (volute) from the motor to expose 

the diffuser and the seal plate.

5.   Remove the two cap screws and diffuser from the seal plate to 

expose the impeller.

6.   Remove the rear cover on the end of the motor opposite the 

impeller.

7.   Secure a 7/16" wrench across wrench flats of shaft to keep the 

shaft from rotating and remove the impeller by hand (standard 

right hand thread). Be sure to hold onto the seal plate when 

removing the impeller from the shaft.

MAINTENANCE

  Disconnect power and release all pressure from 

the system before attempting to install, service, relocate or perform any 

maintenance. Lock the power disconnect in the open (OFF) position. Tag 

out the power disconnect to prevent unexpected application of power.

  Débrancher de la source d’alimentation puis 

dissiper toute la pression du système avant d’essayer d’installer, 

de réparer, de déplacer ou de procéder à l’entretien. Verrouiller 

le sectionneur de courant en position ouverte (OFF). Étiqueter le 

sectionneur de courant pour éviter toute mise sous tension imprévue.

   Protect the pump from freezing during winter 

conditions.

 MISE EN GARDE

   Protéger la pompe du gel pendant l'hiver.

DRAINING THE PUMP

Drain openings are provided on all models.
To drain the pump:
1.   Remove drain fitting and prime plug to vent the system (see 

Figure 7).

2.   Drain all piping to a point below the freeze line.

DRAINING THE TANK

Conventional tanks can be drained by opening an outlet at the 

lowest point in the system. Remove plug or the air volume control 

to vent the tank.
Precharged tanks force virtually all the water from the tank when 

system pressure is released. No draining is necessary.

RESTARTING PUMP

If the pump has been serviced, drained or has not been used for 

some time, be sure there is water in the pump housing (volute) and 

the piping to the well. There must be water in the pump housing 

(volute) at all times when the pump is running to avoid internal 

damage of seal members.

WATERLOGGED TANKS: CONVENTIONAL

When a tank system has an inadequate ratio of air and water, the 

pump will start and stop often and eradically.
1.   Disconnect the power to the pump.
2.   Open the lowest faucet in the system to release all pressurized 

water in the system.

3.   Prime the pump (Priming the Shallow Well Pump on page 6).
4.   Reconnect the power to the pump.

NOTE:

 

As the pump refills the tank with water, the air volume 

control supplies the tank with the correct air to water ratio for the 

system to operate. If the air volume control is good, the pump will 

shut off at the desired cut-off and will be adjusted correctly.

WATERLOGGED TANKS: PRECHARGED

If a precharged tank becomes waterlogged, the bladder is normally 

leaking or broken.
1.   Test the tank by depressing the air valve. The air valve will expel 

water if the bladder is broken.

2.   If broken, replace the tank.

NOTE:

 

Once a bladder is leaking or broken, the bladder cannot be 

repaired. The tank must be replaced.

Содержание SWS50-8.5FX
















Отзывы:

Нет отзывов