background image

 

12 

 

Roll-Up Sheet Door

 

LIMITED WARRANTY 

 

 

 Wayne-Dalton Corp 

 P.O. Box 67- Mt. Hope, Ohio 44660 

 

The Manufacturer warrants the ROLL-UP SHEET DOOR and hardware fittings for a period of ONE YEAR from the time of 

delivery against any defects in workmanship or material.  Manufacturer shall, upon notification, correct such nonconformity at its option, by 

repairing or replacing any defective part or parts.                                                                                                                               

 

NO  EMPLOYEE,  DISTRIBUTOR,  OR  REPRESENTATIVE  IS  AUTHORIZED  TO  CHANGE  THE  FOREGOING 

WARRANTIES IN ANY WAY OR GRANT ANY OTHER WARRANTY ON BEHALF OF MANUFACTURER.  

 

The Manufacturer shall not be responsible for any damage resulting to or caused by its products by reason of installation, improper 

storage, unauthorized service, alteration of products, neglect or abuse, or attempt to use the products for other than the customary usage or 

for their intended purposes.  The ROLL-UP SHEET DOOR warranty becomes null and void if other than Manufacturer’s specified holes are 

drilled.  The above warranty does not cover wear or any damage beyond Manufacturer’s control or replacement labor. 

 

THIS WARRANTY COVERS A COMMERCIAL PRODUCT, THE FOREGOING WARRANTIES ARE IN LIEU OF ALL 

OTHER  WARRANTIES  AND  NO  REPRESENTATIONS,  GUARANTEES,  OR  WARRANTIES,  EXPRESSED  OR  IMPLIED, 

(INCLUDING,  BUT  NOT  LIMITED  TO,  THE  WARRANTY  OF  MERCHANTABILITY  OR  FITNESS  FOR  PARTICULAR 

PURPOSE), ARE MADE BY MANUFACTURER IN CONNECTION WITH MANUFACTURE OR SALE OF ITS PRODUCTS. 

 

Claims for defects in material and workmanship covered by this warranty shall be made in writing to the dealer from whom the 

product was purchased within the warranty period.  Manufacturer may either send a service representative or have the product returned to 

the Manufacturer at Buyer’s expense for inspection.  If judged by Manufacturer to be defective in material or workmanship, the product will 

be replaced or repaired at the option of Manufacturer, free from all charges except authorized transportation and replacement labor. 

 

THE REMEDIES OF BUYER SET FORTH HEREIN ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER REMEDIES.  

THE LIABILITY OF MANUFACTURER, WHETHER IN CONTRACT, TORT, UNDER ANY WARRANTY, OR OTHERWISE, 

SHALL NOT EXTEND BEYOND ITS OBLIGATION TO REPAIR OR REPLACE, AT ITS OPTION, ANY PRODUCT OR PART 

FOUND BY MANUFACTURER TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP.  MANUFACTURER SHALL NOT BE 

LIABLE FOR COST OF REMOVAL OR INSTALLATION OR SHALL NOT BE RESPONSIBLE FOR ANY DIRECT, INDIRECT, 

SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE.  

 

This warranty gives you specific legal rights which may vary from state to state.  However, some states do not allow limitations on 

how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or 

exclusions may not apply to you. 

 

 

 

 

 

 

 

 

 

Wayne-Dalton Corporation 

Door & Systems Division 

2589 County Road 168 

Dundee, OH 44624

 

1-800-795-5095

 

Содержание DS-75













Отзывы: