manualshive.com logo in svg

Wayne-Dalton 464, Инструкция по установке и руководство пользователя, Страница: 4 / 26

Поделиться
Скачать
Wayne-Dalton 464 Скачать руководство пользователя страница 4

2” Track At The Floor:

 

Pre-cast Wall With Corner Angle

1” Overlap

1”

1/2”-5/8”

5/16” x 1” Self 

drilling screw

3/8” x 3” 

Sleeve anchor

Optional 

mounting bracket

4-3/4”

3-1/2” Min. 

Sideroom

3-1/2”

2” Track At The Floor:

 Pre-cast 

Wall Without Corner Angle

1” Overlap

1”

1/2”-5/8”

3/8” x 3” 

Sleeve anchors

Optional 

mounting bracket

4-3/4”

3-1/2” Min. 

Sideroom

3-1/2”

2” Track At The Floor:

 

Steel Jambs

1” Overlap

1”

1/2”-5/8”

3-1/2” Min. Sideroom

3-1/2”

5/16” x 1” Self 

drilling screw

4-1/2” Min.

2” Track At The Floor:

 

Wood Jambs

1”

1/2”-5/8”

4” Min. Sideroom

3-1/2”

5/16” x 1-5/8” 

Lag screw

2” x 6” Jamb Is 

recommended

Flush

3” Track At The Floor:

 

Pre-cast Wall With Corner 

Angle

1” Overlap

3/4”

1/2”-3/4”

5/16” x 1” Self 

drilling screw

3/8” x 3” 

Sleeve anchor

Optional 

mounting 

bracket

5-1/2”

4” Min. 

Sideroom

4-1/4”

3” Track At The Floor:

 

Pre-cast Wall Without 

Corner Angle

1” Overlap

3/4”

1/2”-3/4”

3/8” x 3” 

Sleeve anchors

Optional 

mounting 

bracket

5-1/2”

4” Min. 

Sideroom

4-1/4”

3” Track At The Floor:

 Steel 

Jambs

1” Overlap

3/4”

1/2”-3/4”

4” Min. Sideroom

4-1/4”

5/16” x 1” Self 

drilling screw

5-1/2” Min.

3” Track At The Floor:

 

Wood Jambs

1/2”-3/4”

5-1/2” Min. 

Sideroom

4-1/4”

5/16” x 1-5/8” 

Lag screw

2” x 6” Jamb Is 

recommended

Flush

3/4”

Package Contents

NOTE:

 Depending on the door model, some parts listed will not be supplied if not required. 

Rear Back Hangs may not be included with your door.

4

Содержание 464



























Отзывы:

Нет отзывов