3/8”-16
Hex nut
Horizontal
track angle
3/8”-16 x
3/4” Truss
head bolt
1/4”-20 x
9/16”
Track bolts
1/4”-20
Flange hex
nuts
Horizontal
track
Flag angle
upper slot
Level
IF YOU HAVE ANGLE MOUNT:
To install horizontal track, place the curved end over the
top track roller of the top section. Align the bottom of the horizontal track with the top of the
vertical track. Tighten the horizontal track to the angle mount with (2) 1/4” - 20 x 9/16” track
bolts and (2) 1/4” - 20 flange hex nuts.
3/8”-16
Hex nut
Angle
mount
3/8”-16 x
3/4” Truss
head bolt
1/4”-20 x
9/16”
Track bolts
1/4”-20
Flange
hex nuts
Horizontal
track
Upper slot
Level
Vertical
track
Horizontal
track angle
Next level the horizontal track assembly and bolt the horizontal track angle to the first
encountered slot in the flag angle / angle mount using (1) 3/8” - 16 x 3/4” truss head bolt
and (1) 3/8” - 16 hex nut. Repeat for other side. Remove nail that was temporally holding the
top section in position.
IMPORTANT:
FAILURE TO REMOVE NAIL BEFORE ATTEMPTING TO RAISE DOOR COULD
CAUSE PERMANENT DAMAGE TO TOP SECTION.
Horizontal
track
Level
Level
Horizontal
track angle
Horizontal
track angle
Horizontal
track
Adjusting Top Fixtures
13
NOTE:
Refer to Package Contents / Breakdown of Parts, to determine which Top Fixtures
Assemblies you have.
With horizontal tracks installed, you can now adjust the top fixtures. Vertically align the top
section of the door with the lower sections. Once aligned, position the top fixture slide, out
against the horizontal track. Maintaining the slide’s position, tighten the 1/4” - 20 flange hex
nuts or the 5/16” - 18 hex nut to secure each of the top fixture slide to the top fixture base.
Top fixture
slide(s)
Tighten the 1/4” - 20
Flange hex nuts
Horizontal track
Track roller
Top section
Intermediate
section
Top
section
Top
section
If needed. lock each of the top fixture slides into place using (1) 1/4” - 20 x 9/16” track bolt
and (1) 1/4” - 20 flange hex nut through any two aligning holes.
(1)1/4”-20 x 9/16”
Bolt(s) and (1)
1/4”-20 flange hex
nut(s)
Top
section
Track roller
Top fixture
assembly(s)
Top fixture
slide(s)
Horizontal track
Intermediate
section
Top
section
Top
section
Tighten the 5/16” - 18
hex nut(s)
COUNTERBALANCE
INSTALLATION INSTRUCTIONS
Attaching End Bearing Brackets
14
NOTE:
Refer to Package Contents / Breakdown of Parts, to determine which End Bearing
Brackets you have.
NOTE:
Prior to fastening end bearing brackets into the door jamb, pilot drill using a 3/16”
drill bit.
IMPORTANT:
RIGHT AND LEFT HAND IS ALWAYS DETERMINED FROM INSIDE THE BUILDING
LOOKING OUT.
NOTE:
Depending on your door’s configuration you may have to break the end bearing
brackets apart.
NOTE:
End bearing brackets are right and left hand.
Attach the left hand end bearing bracket through either the end bearing bracket’s upper or
lower slots to the left hand horizontal track angle using (2) 3/8” - 16 x 3/4” truss head bolts
and (2) 3/8” - 16 nuts.
Horizontal track angle
Horizontal track radius
Bend back and fourth to seperate
the (2) end bearing brackets
(2) 3/8”-16
Hex nuts
(2) 3/8”-16 x 3/4”
Truss head bolts
Upper
slots
Lower
slots
Horizontal
track angle
Or
IMPORTANT:
THE END BEARING BRACKET’S LOWER SLOTS ARE USED ON DOORS WITH 12”
RADIUS TRACK; THE UPPER SLOTS ARE USED ON DOORS WITH 15” RADIUS TRACK.
(2) 3/8”-16
Hex nuts
(2) 3/8”-16 x 3/4”
Truss head bolts
Upper
slots
Lower
slots
Left hand
end bracket
Left hand
end bracket
Secure the top of the end bearing bracket to the jamb using 5/16” x 1-5/8” lag screw(s).
Repeat the same process for right hand side.
Jamb
5/16” x 1-5/8”
Lag screws
Or
Left hand
end bracket
Left
hand
end
bracket
13