WAVESTREAM RMC-RRS011-HE01 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 54

WAVESTREAM RMC-RRS011-HE01 Скачать руководство пользователя страница 32

Redundancy Controller

Page

32

Document Number: 90-005-0030_E

Power On

r108

1.

Verify that all cables, units, and waveguides are connected to the RMC.

1.

Turn on the computer where the Wavestream GUI is loaded and
open the GUI application by double-clicking the Wavestream icon.

2.

Turn on power to the RMC.

3.

Apply power to the SSPAs / BUCs.

4.

In the

Serial Ports

field on the GUI, select the appropriate com port; the only valid port for the

RMC is Ethernet.

5.

Press

Start

.

6.

Communication with the unit is established.

7.

The units are queried and status information is displayed for the primary unit.

8.

To view status for the backup / secondary unit press

Rackmount Thread

on the GUI toolbar

9.

Select

Thread A

to view SSPA-A or

Thread B

to view SSPA-B.

Select Power On Setting

To configure the power on setting:



Apply the software TX enable; note that this is not applicable in a redundancy
configuration.



Configure the power on setting in the GUI and save the default TX setting so that it will
be enabled at power up.

«
...
30
31
32
33
34
...
»

Содержание RMC-RRS011-HE01























































Отзывы:

Нет отзывов