background image

 

 

13 

 

2.  RECALL function 

Press STORE  button  two seconds to enter  into RECALL function. 
On  the  left upper corner  shows  XXXX, which  states current  storage serial number. 
On  the  right upper corner  shows  XXXX, which  states how  many  current  storage is used. 
 
Press button  PEAKHOLD shortly  once to scan  data from  0000 to XXXX continuously.   
Press again then  scan again. 
Use button  + & - to select  serial number  XXXX on the  left  upper corner  and record data on  the 
right  upper corner. 
To finish  above RECALL function,  press EXIT  button.   

 
WIRELESS DATA SENDING FUNCTION:

 

1.  Install  and launch  the PC software 
2.  Explore  the CD, read the  USB Driver Installation  documentation  and choose the  appropriat

e driver  for your  PC Operating  System. 

3.   Connect  the USB Wireless Receiver  to your  PC. 

4.  Double click the multimeter  icon 

 or access from the  Start menu  on your  PC and open 

the  operating interface.

 

 

 

 

5.   When  ready, hold  WAVECOM 98 backlit for  2 secs, entering  into wireless sending  state. 

The  RF icon will flash  on the  upper right of LCD. When  the  wireless receiver,  receives the   
signal,  it will  flash  and meanwhile  the  wireless receiver  indicates and the  light  will flash   
synchronously.   

6.  Setting up  COM input  of PC,  

press link button  to ON,  on WAVECOM 98 operating  interface will  show  tested parameter  
data synchronously  and record in the  PC.  

On  the  PC operating interface  you  may  set up a start time and interval  between  each  
recording. 

 

  
The  Meter may  operate at a distance from Wireless receiver up  to about 10M. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание 98





















Отзывы: