wattstopper PW-301 Скачать руководство пользователя страница 4

Страница: 4 / 12

1. Make sure that the power has been turned

OFF

at the circuit breaker.

2. Connect wires to the PW flying leads as shown in the

wiring diagram that is appropriate to the PW model and

electrical supply.

The 2 ground wires (both green) must

be fastened to ground for the sensor to work properly.

3. Attach the sensor to the wall box by inserting screws into

the two wide holes on the top and bottom of the attached

metal bracket. Match them up with the holes in the wall

box and tighten.

4. Turn the circuit breaker

. Wait

one minute, then push the Auto

ON/OFF

switch for each load and

the lights will turn

. There is

a delay due to initial power-up of

the sensor that only occurs during

installation.

5. Test and adjust the sensor if

necessary.

6. Install industry standard

decorator wall switch cover plate

(not included).

INSTALLATION

Red

Black

Neutral

Line

Green

Ground

Blue

Primary

Load

Secondary

Load

Neutral

(optional)

Brown

Yellow

Red

Black

Neutral

Line 1

Green

Ground

Blue

Primary

Load

Brown

Secondary

Load

Line 2

Neutral

(optional)

Yellow

PW-302 and PW-302-347

Bi-Level Wiring

PW-302 and PW-302-347

Dual Circuit Wiring

WARNING

TURN THE POWER OFF AT THE CIRCUIT BREAKER

BEFORE INSTALLING THE SENSOR OR WORKING ON THE LOAD.

#12 – #14 AWG

Cu Wire Only

Strip Gage

1/2"

12.7mm

Visit our website for FAQs: www.wattstopper.com

Load

Red

Black

Neutral

Line

Green

Neutral

(optional)

Ground

Yellow

PW-301 and PW-301-347 Wiring

Side View

Содержание PW-301













Результаты поиска

Содержание PW-301

Отзывы:

Бренды по названию

Популярные бренды

wattstopper PW-301, Руководство по установке

Результаты поиска

Содержание PW-301

Отзывы:

Бренды по названию

Популярные бренды