background image

 

of 

16 

© 

2005     D 

704 

04/05

D 704

04/05

Mixing Station 704

- Data Brochure

WARNING SYMBOL: THIS SYMBOL INDICATES THE PRESENCE OF HAZARDS WHICH 
CAN CAUSE SEVERE PERSONAL INJURY, SUBSTANTIAL PROPERTY DAMAGE OR 
EVEN DEATH IF IGNORED.

The Mixing Station 704 represents a breakthrough in the design, control and installation of radiant systems.  The patent pending design 
combines a variable speed injection mixing control (RMC), injection circulator, system circulator, and air elimination into a single unit.  
Extremely versatile, the Mixing Station 704 can be set up to operate as an outdoor reset control, a setpoint control or a delta T limiting 
control.

General

Mixing 

Station 70

4

Table of Contents

TYPICAL PIPING ------------------------------------------------- 2
GETTING READY ------------------------------------------------ 3
APPLICATION ---------------------------------------------------- 3
DESIGN PROCEDURE ----------------------------------------- 3
INSTALLATION OF MIXING STATION 704 --------------- 4
OUTDOOR RESET MODE ------------------------------------ 5
OUTDOOR RESET SETTINGS ------------------------------ 5
SETPOINT AND DELTA T MODE --------------------------- 6
SETPOINT AND DELTA T SETTINGS --------------------- 7
BOILER OPERATION MODE --------------------------------- 7

SET UP OF RADIANT MIXING CONTROL --------------- 8
DISPLAY OPERATION ---------------------------------------- 11
TROUBLE SHOOTING ---------------------------------------- 13
ERROR MESSAGES ------------------------------------------- 14
REPLACING CARTRIDGE ASSEMBLY  ----------------- 14
REPLACING THE CHECK VALVE  ------------------------ 15
TECHNICAL DATA ---------------------------------------------- 15
CLEANING -------------------------------------------------------- 16
LIMITED WARRANTY STATEMENT ----------------------- 16

MIXING STATION 704 (RMB)

RADIANT MIXING CONTROL (RMC)

Содержание tekmar 704

















Отзывы: