background image

 

15 of 16 

 © 2005          D 704 - 04/05

Technical Data

1. Disconnect the electrical supply.
2. Reduce system pressure to 0 psi and allow system to return to room temperature. Isolate the Mixing Station 704 by closing the 
service valves or draining the system.
3. Remove the Boiler Supply connection to the Mixing Station 704.
4. Remove snap ring.
5. Remove the check valve, using needle nose pliers.
6. Install replacement check valve by pressing the valve into the casing until it is fi rmly seated.
7. Install the snap ring.
8. Reconnect the Boiler Supply connection to the Mixing Station 704.
9. Follow the “Installation” procedure to start up the Mixing Station 704.

Replacing the Check Valve

PERFORMANCE DATA

Flow Range:  ......................................... 0 - 15.5 GPM
Head Range:  ........................................ 0 - 15 Feet
Minimum Fluid Temperature:   ............... 32°F (0°C)
Maximum Fluid Temperature:   .............. 180°F (82°C)
Maximum Working Pressure:   .............. 125 psi (875 kpa)
Connections:  ......................................... 3/4” NPT
C US UL Mark 
FOR INDOOR USE ONLY

MATERIALS OF CONSTRUCTION

Casing (body): ....................................... Bronze
Stator Housing: ...................................... Steel
Cartridge: ............................................... Stainless  Steel
Impeller: ................................................. Non-Metallic
Shaft: ..................................................... Ceramic
O-Ring & Gaskets: ................................. EPDM

ELECTRICAL DATA CHART

Voltz ....................................................... 120
Hz .......................................................... 60
Ph .......................................................... 1
Amps ..................................................... 2
RPM ....................................................... 3250
HP .......................................................... 1/40 & 1/25

DIMENSIONS & WEIGHT

Ship Weight: 18.5 lbs (8.4 kg)

Motor Type ............................................. Permanent Split Capacitor 

Impedance Protected

CONTROL ADJUSTMENT MENU

Mixing Setpoint Temperature ................. 60 to 185°F (16 to 85°C)
Maximum Temperature Difference 
Between Mixing Supply and Return ...... 10 to 70°F (-12 to 21°C), Off
Design Outdoor Air Temperature ........... -60 to 32°F (-51 to 0°C), Off
Design Heating System Supply Water 
Temperature .......................................... 70 to 185°F (21 to 85°C)
Maximum Mixing Target Supply ............. 80 to 185°F (27 to 85°C)
Minimum Mixing Target Supply 
Fluid Temperature .................................. 35 to 150°F (2 to 66°C), Off
Minimum Boiler Target Supply 
Water Temperature ................................ 80 to 180°F (27 to 82°C), Off
Warm Weather Shut Down .................... 35 to 100°F (2 to 38°C), Off
Units ...................................................... °F or °C

2 3/8” (60 mm)

2 3/8” (60 mm)

4 1/2” (114 mm)

CLEARANCE FOR

VENT REMOVAL

11 1/2”

(290 mm)

11 1/2”

(290 mm)

8 1/4”

(209 mm)

8 1/4”

(209 mm)

8 1/8”

(206 mm)

8 1/8”

(206 mm)

7 1/4”

(184 mm)

7 1/4”

(184 mm)

1”

(25 mm)

1”

(25 mm)

1”

(25 mm)

6 1/2”

(165 mm)

6 1/2”

(165 mm)

6 1/2”

(165 mm)

6 1/2”

(165 mm)

6 7/8”

(175 mm)

6 7/8”

(175 mm)

4” (101 mm)

4” (101 mm)

3 3/8” (86 mm)

3 3/8” (86 mm)

2 3/4”

(70 mm)

2 3/4”

(70 mm)

14”

(360 mm)

14”

(360 mm)

1 5/8” (41 mm)

1 5/8” (41 mm)

3/4” (19 mm)

Содержание tekmar 704

















Отзывы: