background image

© 2019 tekmar  306V_D - 10/19

3 of 12

Preparation

Tools Required

 -----------------------------------------------------------------------------------------

•  tekmar or jeweler screwdriver
•  Phillips head screwdriver

•  Needle-nose pliers
•  Wire stripper

Materials Required

 -------------------------------------------------------------------------------------

Packaging Contents

 ------------------------------------------------------------------------------------

•  18 AWG LVT solid wire (low-voltage connections)
•  14 AWG solid wire (line-voltage connections)

•  Four 1/8" - 1" wood screws

Installation

•  1 Zone Valve Control 306V
•  2 Spare fuses (located in cover)

•  1 Installation and Operation Manual 306V_D

The installer must ensure that this control and its wiring are 

isolated and/or shielded from strong sources of electromagnetic 

noise. Conversely, this Class B digital apparatus complies 

with Part 15 of the FCC Rules and meets all requirements of 

the Canadian Interference-Causing Equipment Regulations. 

However, if this control does cause harmful interference to 

radio or television reception, which is determined by turning 

the control off and on, the user is encouraged to try to correct 

the interference by re-orientating or relocating the receiving 

antenna, relocating the receiver with respect to this control, 

and/or connecting the control to a different circuit from that 

to which the receiver is connected.
Cet appareil numérique de la classe B respecte toutes les exi-

gences du Règlement sur le matériel brouilleur du Canada.

Radio Frequency Interference

Location

•  Keep the control dry. Avoid potential leakage onto the control.
•  Maintain relative humidity less than 90% in a non-condensing environment.
•  Avoid exposure to extreme temperatures beyond 32-122°F (0-50°C).
•  Install away from equipment, appliances, or other sources of electrical interference.
•  Install to allow easy access for wiring, viewing, and adjusting the display screen.
•  Install approximately 5 feet (1.5 m) off the finished floor.

•  Locate the control near pumps and/or zone valves if possible.

•  Provide a solid backing which the enclosure can be mounted to. Example: plywood or wall studs.

•  Use the conduit knockouts provided on the upper, lower, and back of the enclosure for wiring.

Installing the Enclosure

To prevent the risk of personal injury and/or death, make sure power 

is not applied to the control until it is fully installed and ready for final 

testing. All work must be done with power to the circuit being worked 

on turned off.
Please be aware local codes may require this control to be installed 

or connected by an electrician.

Содержание tekmar 306V













Отзывы: