background image

Setting the Rate-of-Flow Control Valves

STEP 1

Pre-set pilots as noted:

Rate of Flow 

– Adjust OUT, counterclockwise, to start valve at a lower flow rate.

Opening and Closing Speed

 – Turn the adjustment screws on the Closing Speed and Opening Speed Controls, if the main valve is so 

equipped, OUT, counterclockwise, 1½ to 2½ turns from full closed position.

STEP 2

Energize the solenoid to check actuation and to confirm connec-
tion to power source and so that initial valve filling is against the 
closed solenoid.

STEP 3

To ensure proper operation, any trapped air will need to be bled 
off the valve cover during startup. The ACV includes a bleed valve, 
use a flat head screwdriver to slowly open the valve (See Figure 1).

STEP 4

Pressure the line, by opening the upstream isolation valve slowly. 
Air is vented through the air bleed valve. Tighten the fitting when 
liquid begins to vent (See Figure 1). 

Repeat the process until no air is trapped in the system.

STEP 5

Actuate the solenoid to open the main valve, checking that the 
main valve opens.

Globe

Angle

Size (in)

1

 

1/4

1

 

1/2

2

21/2

3

4

6

8

10

12

14

16

20

24

A (in)

16

16

20

22

22

24

32

34

38

44

48

52

56

56

B (in)

10

10

12

14

14

16

24

26

28

30

34

40

48

48

Size (in)

1

 

1/4

1

 

1/2

2

2

 

1/2

3

4

6

8

10

12

14

16

C (in)

16

16

20

22

22

24

32

34

38

44

48

52

D (in)

10

10

12

14

14

16

24

26

28

30

34

40

Counterclockwise to OPEN 

bleed valve

The following tables detail the recommended minimum valve servicing dimensions.

          

B

          

          

FLOW

FLOW

FLOW

          

FLOW

Valve Servicing Dimensions

Figure 1 

Position Indicator

IOM-ACV-114-1_6114-1 2115 

EDP# 1917071 

© 2021 Watts         3

Содержание LFM114-1













Отзывы: