Watts LC-100 Series Скачать руководство пользователя

Страница: 32 / 52

SXT Diagnostics

Viewing Diagnostic Data

The SXT controller records and maintains diagnostic data to assist

with servicing and troubleshooting the water treatment system.

Abbreviation Parameter

Description

Flow Rate

Displays the current outlet

flow rate.

Peak Flow

Rate

Displays the highest flow rate

measured since last regeneration.

Hours in

Service

Displays the total hours that the

unit has been in service since

last regeneration.

Volume

Used

Displays the total volume of

water treated by the unit since

last regeneration.

Reserve

Capacity

Displays the system’s reserve

capacity calculated from the

system capacity, feed water hard-

ness, and safety factor.

Totalizer

Volume

Displays the total volume of

water used by the unit since last

installation or last reset.

Software

Version

Displays the software version

installed on the controller.

NOTE: Some items may not be shown depending on

control configuration. The control will discard any

changes and exit the Diagnostics View if a button

is not pressed for 60 seconds.

Figure 25

Figure 26

Figure 27

Diagnostics View Steps

1. Press the Up and Extra Cycle buttons for five seconds while

in service.

2. Use this display to view the current Flow Rate. This option set-

ting is identified by “FR” in the upper left corner of the screen.

3. Press the Up button. Use this display to view the Peak Flow

Rate since the last regeneration cycle. This option setting is

identified by “PF” in the upper left corner of the screen.

4. Press the Up button. Use this display to view the Hours in

Service since the last regeneration cycle. This option setting is

identified by “HR” in the upper left corner of the screen.

Содержание LC-100 Series





















































Результаты поиска

Содержание LC-100 Series

Отзывы:

Похожие инструкции для LC-100 Series

Бренды по названию

Популярные бренды

Watts LC-100 Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание LC-100 Series

Отзывы:

Похожие инструкции для LC-100 Series

Бренды по названию

Популярные бренды