background image

Page 20

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Limited Warranty

What your Warranty Covers:

If any part of your Reverse Osmosis System is defective in workmanship (excluding replaceable filters and membranes), return 

unit after obtaining a return authorization (see below), less tank, within 1 year of original retail purchase, WATTS will repair or, 

at WATTS option, replace the system at no charge.

How to obtain Warranty Service:

For warranty service, call 

800-659-8400 

for documentation and a return authorization number. Once the return authorization 

number has been created, ship your Reverse Osmosis unit (less tank) to our factory, freight and insurance prepaid, with proof of date 

of original purchase. Include a note stating the problem experienced and include your name, address and your return authorization 

number. No returns will be accepted with out the proper return authorization number. WATTS will repair it, or replace it, and ship 

it back to you prepaid.

What this warranty does not cover:

This warranty does not cover defects resulting from improper installation, (contrary to WATTS printed instructions), from abuse, 

misuse, misapplication, improper maintenance, neglect, alteration, accidents, casualties, fire, flood, freezing, environmental factors, 

water pressure spikes or other such acts of God.

 

This warranty will be void if defects occur due to failure to observe the following conditions:

1.  The Reverse Osmosis System must be hooked up to a potable municipal or well cold water supply.

2.  The hardness of the water should not exceed 10 grains per gallon, or 170 ppm.

3.   Maximum incoming iron must be less than 0.2 ppm.

4.  The pH of the water must not be lower than 2 or higher than 11.

5.  The incoming water pressure must be between 40 and 85 pounds per square inch.

6.  Incoming water to the RO cannot exceed 105 degrees F (40 degrees C.)

7.  Incoming TDS/Total Dissolved Solids not to exceed 1800 ppm.

 

8.    Do not use with water that is micro biologically unsafe or of unknown quality without 

 

        adequate disinfection before or after the system.

This warranty does not cover any equipment that is relocated from the site of its original installation.

This warranty doe not cover any charges incurred due to professional installation.

This warranty does not cover any equipment that is installed or used outside the United States of America and Canada.

LIMITATIONS AND EXCLUSIONS:

WATTS WILL NOT BE RESPONSIBLE FOR ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY 

AND FITNESS FOR A PARTICULAR PURPOSE.  WATTS WILL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR 

CONSEQUENTIAL DAMAGES, INCLUDING TRAVEL EXPENSE, TELEPHONE CHARGES, LOSS OF REVENUE, LOSS 

OF TIME, INCONVENIENCE, LOSS OF USE OF THE EQUIPMENT, AND DAMAGE CAUSED BY THIS EQUIPMENT 

AND ITS FAILURE TO FUNCTION PROPERLY.  THIS WARRANTY SETS FORTH ALL OF WATTS RESPONSIBILITIES 

REGARDING THIS EQUIPMENT.

OTHER CONDITIONS:

If WATTS chooses to replace the equipment, WATTS may replace it with reconditioned equipment. Parts used in repairing or 

replacing the equipment will be warranted for 90 days from the date the equipment is returned to you or for the remainder of the 

original warranty period, whichever is longer. This warranty is not assignable or transferable. 

YOUR RIGHTS UNDER STATE LAW:

Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation 

of incidental or consequential damages, so the above limitations or exclusions may not apply. This warranty gives you specific 

legal rights, and you may have other legal rights which vary from state to state.

Содержание GTS450





















Отзывы: