Limited Warranty:
Watts Regulator Co. (the “Company”) warrants each product to be free from defects in material and workmanship under normal usage for a period of one year from the date of
original shipment. In the event of such defects within the warranty period, the Company will, at its option, replace or recondition the product without charge.
THE WARRANTY SET FORTH HEREIN IS GIVEN ExPRESSLY AND IS THE ONLY WARRANTY GIVEN BY THE COMPANY WITH RESPECT TO THE PRODuCT. THE COMPANY MAKES NO OTHER
WARRANTIES, ExPRESS OR IMPLIED. THE COMPANY HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLuDING BuT NOT LIMITED TO THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICuLAR PuRPOSE.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for breach of warranty, and the Company shall not be responsible for any incidental, special
or consequential damages, including without limitation, lost profits or the cost of repairing or replacing other property which is damaged if this product does not work properly, other costs resulting
from labor charges, delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions, chemical, or any other circumstances over which the Company has no
control. This warranty shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or alteration of the product.
Some States do not allow limitations on how long an implied warranty lasts, and some States do not allow the exclusion or limitation of incidental or consequential damages. Therefore the above
limitations may not apply to you. This Limited Warranty gives you specific legal rights, and you may have other rights that vary from State to State. You should consult applicable state laws to
determine your rights.
SO FAR AS IS CONSISTENT WITH APPLICABLE STATE LAW, ANY IMPLIED WARRANTIES THAT MAY NOT BE DISCLAIMED, INCLuDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICuLAR PuRPOSE, ARE LIMITED IN DuRATION TO ONE YEAR FROM THE DATE OF ORIGINAL SHIPMENT.
WARNING:
This product contains chemicals known
to the State of California to cause cancer and birth
defects or other reproductive harm.
For more information: www.watts.com/prop65
IS-FS-200-W 1517
EDP#2915183
© 2015 Watts
USA:
Tel: (978) 689-6066 • Fax: (978) 975-8350 • Watts.com
Canada:
Tel: (905) 332-4090 • Fax: (905) 332-7068 • Watts.ca
Latin America:
Tel: (52) 81-1001-8600 • Fax: (52) 81-8000-7091 • Watts.com
A Watts Water Technologies Company
Pressure — Temperature
Maximum Service Pressure: 160 psi
Maximum Temperature: 250°F
Enclosure: NEMA type 1 (for indoor use only).
Formed sheet metal construction.
Powder coated cover, zinc plated
chassis, brass body. Not for use in
hazardous locations.
Contacts: SPDT switch
7.4 FLA, 44.4 LRA@120VAC Motor Duty
Pilot Duty Rating: 125V@120/240VAC
Ambient Temp. Range: 32°F-176°F (0°C-80°C)
Media Temp. Range: 32°F-250°F (0°C-121°C)
Pipe Connection: 1"NPT - Brass
Conduit Access: 2 openings for 1/2" conduit
Usage: 1" to 6" pipe sizes
(see Flow Chart - Table 1)
Installation Instructions
Trimming the Paddles
1. The stainless steel paddles (set of 4 supplied)
must be trimmed to the appropriate length for
the pipe diameter being used. Use the template
at the right of this page as a cutting guide.
Follow the curve indicated as closely as pos-
sible. Standard shears or tin snips can be used.
Stacking the Paddles
2. After trimming, the paddles must be
stacked as shown in
Figure 2
and
then screwed onto the stem of the
flow switch.
The correct orientation of the paddles
to the flow of the fluid is essential.
Installing the Tee
3. The Flow Switch must be installed
in a 1" NPT threaded pipe fitting. If a
reducing bushing or welded
fitting is required, the length
must be kept to a minimum
to insure that the paddle
can move freely in the run
of the pipe without coming
in contact with the bush-
ing or fitting. Tighten the
Flow Switch with a 1
5
/
8
"
box wrench or adjustable
wrench applied to the
brass nut only.
Do not
tighten by grasping the
enclosure.
Allow a 1
3
/
4
" space from the bottom
of the enclosure to the top of the tee
(Figure 3)
and be sure that the arrow on the side of the
enclosure is in the direction of the flow.
The paddle must not touch the inside wall of the
opposite side of the pipe. If there is any contact,
additional trimming is required.
Wiring
4. ENERGIZE CIRCUIT UPON FLOW
Flow Switch will activate load (alarm, light, relay,
motor starter, etc.) when flow occurs.
ENERGIZE CIRCUIT UPON NO FLOW
Flow Switch will activate load (alarm, light, relay,
motor starter, etc.) when no flow occurs.
Adjusting Sensitivity
5. To
INCREASE
sensitivity
(switch acti-
vates at a
lower flow
rate), turn the
adjustment
screw counter-
clockwise.
To
DECREASE
sensitivity (switch activates at
a higher flow rate), turn the adjustment screw
clockwise.
NOTICE
NOTICE
FIGURE 2
FIGURE 3
FIGURE 4
COMMON (COM)
FLOW OPENS CIRCUIT (NC)
FLOW CLOSES CIRCUIT (NO)
