background image

Drain Saddle Installation - Fits standard 
1 ¼” – 1 ½” drain pipes

Step 8

Step 9

Step 10 

(cont.)

Step 10

The drain saddle must be mounted at least 1 

½” above the nut of the P-trap or cross bar 

from the garbage disposal to insure proper 

drainage.  Assemble the drain saddle around 

the drain pipe at the best available location.  

The small square black foam gasket with a 

circle cut out of the middle must be applied to 

the inside of the drain saddle. Remove sticky 

tape backing and stick to the drain saddle as 

shown.

Locate the drain saddle kit in the parts bag.

Do not over tighten the screws.  It may crack the drain 

saddle.

With the drain saddle secured 

onto the drain pipe, using a 1/4” 

drill bit installed in your electric 

drill, insert the drill bit through 

the opening in the drain saddle 

and drill through the drain pipe.

Step 11

It is very important to keep the 

drill centered to prevent  dam-

age of the drain saddle while 

drilling.

Locate the red 1/4” tube in the parts bag. The 

permeate pump is mounted on the bottom side 

of the system’s metal bracket. Remove the 

blue plug from the permeate pump’s 1/4” quick 

connect port. Connect one end of the red 1/4” 

tube to the open 1/4” port on the permeate 

pump. 

Next, slip the open end of the red 1/4” tube 

through the black compression nut included in 

the drain saddle kit.  Insert the red 1/4” tube 

into the opening of the drain saddle, hand 

tighten the black nut, then add 1/4 turn with a 

wrench.

The 3/8” drain tube must be as SHORT and  STRAIGHT 

as possible from the RO faucet to the drain saddle, 

making a downward slope from faucet to drain saddle 

to allow for proper drainage. This is a gravity fed line 

and if there is any  bend or dip in the tube, the rinse 

water will not flow into the drain properly.  Water may 

back up and come out  the air gap hole in the back of 

the faucet.  

Step 12

* Non Air-Gap Faucet 

(This system 

doesn’t come with a faucet. The below notes 
on the faucet installation are for reference only)

 

Single Tube (1/4” Drain Saddle):

System Drain Connection

The permeate pump is mounted on the bottom side of the 

system’s 

metal bracket. Remove the blue plug from the permeate 

pump port. 

Connect the open end of the red 1/4” tube attached to 

the RO faucet to the open 1/4” quick connect port on the 

permeate pump.

* Air-Gap Faucet 

(This system doesn’t come with a 

faucet. The below notes on the faucet installation are for 
reference only)

 

Three Tubes (3/8” Drain Saddle):

If your RO faucet is non-air 

gap (Single Tube) use 1/4” 

Drain Saddle. 

If your RO faucet is air gap 

(Three tubes) use the 3/8” 

Drain Saddle.

Measure the 3/8” drain tube from the RO faucet to the 

drain saddle on the drain pipe and make a straight cut to 

the correct length. Slip the 3/8” tube open end through 

the black compression nut.  Insert the 3/8” tube into the 

opening of the drain saddle, hand tighten the black nut, 

then add 1/4 turn with a wrench.

Feed Water Valve Installation Continued

If you have a garbage disposal, do not install the drain 

saddle near it.  Installation of the drain saddle must be 

either above the garbage disposal, or if a second sink 

drain is available, install it above the cross bar on the 

second drain.  Installation of the drain saddle near a 

garbage disposal may cause the drain line to plug.

Using Phillips screw driver tight-

en screws evenly and securely 

on both sides of the drain sad-

dle. Keep the plastic compres-

sion nut off at this time.

Содержание FMRO4G-ERP-75





















Отзывы: