Watts FMRO4G-ERP-75 Скачать руководство пользователя страница 5

Make sure the surroundings of the sink are 

cooled  before mounting  the faucet  to the 

sink after drilling and remove all sharp edges. 

Step 3

Step 4

Determine desired  location  for  the RO faucet 

on your sink and place a piece of masking 

tape over where the hole is  to be drilled.  Mark 

the center of the hole on the tape.

Step 1

Using a variable speed drill set on the slowest 

speed, drill a 

1

/

8

“ pilot hole through both por-

celain and metal casing of sink at the marked 

center of  the desired location. Use lubricating 

oil or liquid soap to keep the drill bit  cool (If 

drill bit gets hot it may cause the porcelain to 

crack or chip). 

Using a 1 ¼” hole saw, proceed to drill the 

large hole.  Keep drill speed on  the  slowest 

speed and use lubricating oil or liquid soap to 

keep the hole saw cool during cutting.

Step 2

Punch a Hole for the Faucet in a Stainless Steel Sink 

(This system doesn’t come with a faucet. The below notes on the faucet installation are for reference only)

 

Drill a pilot hole & use the Hole Punch and an 

adjustable wrench to punch the hole in the 

sink.

Step 5

If  mounting faucet to a Stainless Steel Sink  you will need 

a Hole Punch.  The  faucet opening should be centered 

between  the back splash and the edge of the sink, ideally 

on the same side as the vertical drain pipe.

Water supply line to the system must be from 
the cold water supply line only.  

Hot water will severely damage your system.

Configuration for 3/8”

 

(With Brass Fittings)

* Insert White Washer

Hot

Supply

Cold

Supply

Configuration for 1/2”

 

(Without Brass Fittings)

Plastic Valve Configuration:

*Washer

Feed Water Valve Installation

Most sinks are pre drilled with 1 ½” or 1 ¼” diameter hole 

that you can use for your RO faucet. (If you are already 

using it for a sprayer or soap  dispenser, see step 1)

Porcelain sinks are extremely hard and can crack or chip 

easily. Use extreme caution when drilling. 

NOTICE

NOTICE

Drill a Hole for the Faucet in a Porcelain Sink 

(This system doesn’t come with a faucet. The below notes on the faucet installation are for reference only)

Содержание FMRO4G-ERP-75





















Отзывы: