background image

Benchmark 750-3000 Boiler Installation & Startup Manual

 

 SECTION 4 – INITIAL START-UP 

 

OMM-0121_D

  •

  GF-205  

  5/9/2019            

Technical Support

  

  (800) 526-0288  

  Mon-Fri, 8 am - 5 pm EST            Page 70  of 122 

 

PROPANE Combustion Calibration Instructions 

 

Valve Position 

Oxygen (O

2

) % 

Nitrogen oxide (NO

x

Carbon Monoxide (CO) 

BMK 3000

 

85% 

5.2% ± 0.2%

 

≤100 ppm

 

<150 ppm

 

65% 

5.4% ± 0.2%

 

<100 ppm

 

<150 ppm

 

45% 

6.0% ± 0.2% 

<100 ppm 

<150 ppm 

30% 

6.4% ± 0.2% 

<100 ppm 

<100 ppm 

18% 

6.4% ± 0.2% 

<100 ppm 

<100 ppm 

 

* NOTE: 

Set the Valve Position at 18% but make adjustments to the Combustion Calibration value 
designated as 16%. 
 

NOTE:  

If NO

x

 readings exceed the target values in Table 4-6, increase the O

2

 level up to 1% higher 

than the listed calibration range shown in the table. Record the increased O

2

 value on the 

Combustion Calibration sheet.  

31. 

If the oxygen level at the 18% valve position is too high and the Blower voltage is at the 
minimum value, you can adjust the TAC screw, which is recessed in the top of the Air/Fuel 
Valve (see Figure 4-4). Rotate the TAC screw 1/2 turn 

clockwise

 (CW) t

o add fuel and 

reduce the O

2

 

to the specified level. Recalibration 

MUST

  be performed again from 60% 

down to the lowest valve position after making a change to the TAC screw. 

 
This completes the PROPANE gas combustion calibration procedure.

 

  

 

 

 

 

Содержание Benchmark Aerco OMM-0122



























































































































Отзывы: