background image

Standard Components

Operation

The Pressure Sustaining and Solenoid (On-Off) ACV is designed to 
permit flow when upstream pressure is above the adjustable set-
point of the control pilot, and throttle toward closed when upstream 
pressure falls below the adjustable setpoint. It is controlled by a 
normally closed control pilot designed to: 1) Open (allowing fluid out 
of the main valve cover chamber) when upstream pressure is above 
the adjustable setpoint, and, 2) Close (allowing fluid to fill the main 
valve cover chamber) when upstream pressure is below the adjust-
able setpoint. An increase in upstream pressure causes the valve to 
modulate toward an open position. A decrease in upstream pres-
sure causes the valve to modulate toward a closed position.

The Solenoid Pilot will either open to allow regulating action, or 
close the valve drip-tight when energized. Specify energize to open 
or close the Main Valve and voltage PRIOR to ordering.

When the valve is located “in line” connecting two distribution 
zones, the valve acts as a Pressure Sustaining Control Valve. When 
pressure in the upstream zone falls below the pilot setting, the valve 
modulates toward a closed position, sustaining pressure in the 
upstream zone. The valve will close, if necessary, until upstream 
pressure is above the pilot setting. The valve should be specified to 
include the optional opening speed control and position indicator 
when used for Pressure Sustaining applications.

1

X

X

X

Y/FC

3

(AOS)

1

2

P/L

4

CLOSES VALVE

OPENS VALVE

FLOW

1.  Clear the line free of slag and other debris.

2.  Install the valve so that the FLOW ARROW marked on the valve body/tag corresponds to flow through the line.

3.  Close upstream and downstream isolation valves.

4.  Open the isolation ball valves in the control tubing if so equipped. Failure to open these will prevent the valve from functioning 

properly.

5.  Connect solenoid wiring leads to the desired switching device, using safe, standard electrical procedures.

6.  Install pressure gauge at a location upstream of the valve.

Start-up of an automatic control valve requires that proper procedures be followed. Time must be allowed for the valve to react to 
adjustments and the system to stabilize. The objective is to bring the valve into service in a controlled manner to protect the system 
from damaging over-pressure.

1 – Main Valve (905GD - Single Chamber) 

2 – Pressure Sustaining Control 

3 – Adjustable Closing Speed

4 – 2-Way Solenoid

X – Isolation Cocks

Installation

920GD-15 (Globe) Pressure Sustaining Control Valve with 
Solenoid (On-Off) Feature

2          IOM-A-ACV-920-15_620-15   2115 

EDP# 1917048 

© 2021 Watts

Содержание Ames 620GD-15













Отзывы: