background image

 

 SECTION  2: INSTALLATION  

 

   

 

 2.14  BST Sequencing Isolation Valve Installation 

All CFR units are pre-wired with a connection for an optional motorized

 

external sequencing isolation valve 

(P/N 

92084-TAB

). This valve is an integral component of AERCO

’s on-board Boiler Sequencing Technology 

(BST) solution. BST allows sites with multiple boilers to have one boiler, designated the 

“Manager,” 

manage the other boilers at the site, designated as 

“Clients” in such a way that the efficiency of the entire 

boiler array is maximized. 

When operated with the BST system, the BST Manager controls its own isolation valve and sends signals 
to BST Clients to open or close their isolation valves. After boiler load is satisfied, its isolation valve remains 
open for a time interval defined in the 

SH Valve Close Delay

 parameter in the 

Advanced Setup 

  BST 

Cascade 

 Operating Controls 

 Sequencing Controls

 menu (default = 1 minute), then closes. 

NOTE:

 

SH Valve Close Delay

 appears only if 

Unit Mode

 (in 

Main Menu 

 Advanced Setup 

  BST Cascade  

  

Cascade Configuration

) equals 

BST  Manager

Once the system load is satisfied and all Client units have stopped firing, the BST Manager opens the 
isolation valves of all Client units. 

The implementation of BST, and the installation and use of this valve, is optional. However, 

when BST is 

implemented

use of this valve is

 

strongly recommended

Installation consists of installing the sequencing isolation valve in the hot water outlet pipe, and then 
connecting it to the pre-wired connector on the shell harness, as described below. 

NOTE:

 The pre-programmed Sequencing Isolation Valve control is available only from AERCO. It is 

installed only on boilers that are part of a Boiler Sequencing Technology cascade. Refer to 

OMM-0164

 

Section 7: 

Boiler Sequencing Technology

 for configuration. 

 

Sequencing Isolation Valve Installation Instructions 

1. 

Install the sequencing isolation valve in the boiler’s hot water outlet pipe.  

 

Figure 2-17:  Sequencing Isolation Valve Installed 

 

 

HOT WATER 

OUTLET 

AERCO  

SEQUENCING 

ISOLATION VALVE 

Содержание AERCO CFR 3000


























Отзывы: