Watts AERCO Benchmark OMM-0136 Скачать руководство пользователя страница 93

Страница: 93 / 153

Benchmark Platinum-Edge [II]: Operation-Service Manual

SECTION 7

– BOILER SEQUENCING TECHNOLOGY

OMM-

0137_E • GF-211 • 12/13/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

153

7.3.3 Option 3 Outdoor Reset: Direct Wired Header Temp Sensor &
Direct Wired Outdoor Temp Sensor

OPTION 3

Instructions: Outdoor Reset, Direct Wired Header Temp Sensor & Outdoor Temp

Sensor

NOTE:

Both

Header Temp Sensor

and

Outdoor Temp Sensor

must be wired. See the

Edge

Controller Manual

(OMM-0139, GF-213) for more information.

Step 1: DIRECT WIRED

HEADER TEMP SENSOR WIRING

– BST MANAGER Unit

1. On the

BST Manager

unit, connect the

Header Temp Sensor

to the I/O board terminal

strip

, terminals

(

Supply

)

and

(

Supply Header

-).

2. Connect the shield to any

Shield

terminal, such as terminal

on strip

NOTES:

•

The

Header Temp Sensor

must be installed between 2 and 10 feet (0.61 and 3.1m)

downstream of the LAST boiler in the plant’s supply water header.

•

Shielded pair 18 - 22 AWG cable is recommended for

Header Temp Sensor

wiring.

There is no polarity to be observed. The ground for the shield is at the

Shield

terminal

on the I/O the board. The sensor end of the shield must be left free and ungrounded.

Step 2: DIRECT WIRED

OUTDOOR TEMP SENSOR WIRING

– BST MANAGER Unit

1. On the

BST Manager

unit, connect the

Outdoor Temp Sensor

to the I/O board terminal

strip

, terminals

(

Outside Temp

)

and

(

Outside Temp

-).

2. Connect the shield to any

Shield

terminal, such as terminal

on strip

NOTES:

•

Twisted shielded pair 18 - 22 AWG cable is recommended for

Header Temp Sensor

wiring. There is no polarity to be observed. The sensor end of the shield must be left
free and ungrounded.

•

The

Outdoor Temp Sensor must

be mounted on the

North side of the building

where an average outside air temperature is expected. The sensor must be shielded
from direct sunlight as well as impingement by the elements. The

Outdoor Temp

Sensor

may be wired up to 200 feet (61m) from the boiler.

OUTDOOR TEMP SENSOR

I/O BOARD, STRIP J3

HEADER TEMP SENSOR

5 Supply Header-

3 Shield

I/O BOARD STRIP J3

4 Supply

2 Outside Temp -

3 Shield

1 Outside Temp +

Содержание AERCO Benchmark OMM-0136


























































































































































Результаты поиска

Содержание AERCO Benchmark OMM-0136

Отзывы:

Похожие инструкции для AERCO Benchmark OMM-0136

Бренды по названию

Популярные бренды

Watts AERCO Benchmark OMM-0136, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание AERCO Benchmark OMM-0136

Отзывы:

Похожие инструкции для AERCO Benchmark OMM-0136

Бренды по названию

Популярные бренды