Watts AERCO 58015-04 Скачать руководство пользователя

Страница: 10 / 20

Benchmark 3.0LN 24-Month Maintenance Kit 58015-04

Technical Instruction Document

TID-0135_0C

/12/2017

AERCO International, Inc.

•

100 Oritani Dr.

•

Blauvelt, New York 10913

•

Phone: 800-526-0288

Page 10 of 20

3. Place the new burner housing gasket (P/N

81019

) on top of the blower,

nsuring is

positioned correctly in relation to the burner housing’s mounting holes.

4. Position the burner housing on the blower and the burner flange, aligning it with both

burner and blower.

5. Reinstall the the six (6) 1/4-20 screws that connect the burner housing to the blower, but

only hand-tighten them at this point, to ensure proper positioning.

6. If there was an extension ring around the burner at disassembly, replace it.

7. Add one 3/8” flat washers to each of the eight (8) mounting studs coming up through the

burner flange, removed in section 6.1.1, step 7.

IMPORTANT!

It is imperative that the burner housing is fully tighten to the top of the heat
exchanger

BEFORE

its other end is bolted to the blower.

8. Apply Loctite 246 to the mounting studs and then loosely tighten the eight (8) 3/8-16 nuts

attaching the burner housing to the burner, and then

torque the eight nuts in a star (or

alternating) pattern to 35 ± 5 ft./lbs.

to to ensure a uniform seal.

9. Fully tighten the the six (6) 1/4-20 screws hand-tighten in step 5 to fully connect the burner

housing to the blower.

DO NOT ATTEMPT

to pull the burner housing down to meet the

blower. If there is a gap, adjust the blower mounting plate till the blower contacts the
housing.

10. Check to ensure that the grounding screw is reinstalled. Also, ensure that conductive,

high-temperature, anti-seize compound is applied to the threads of the ground screw.

11. Reinstall the staged ignition assembly with the new gas injector gasket (P/N

81070

) on the

burner housing using the two (2) 10-32 screws removed in section 6.1.1, step 5.

12. After servicing is complete, perform a water bubble test during purge to ensure the burner

gaskets are providing a good seal, as specified in section 7.2.

6.1.3 Igniter Replacement

Complete the instructions below on Benchmark 3.0 LN units to reinstall the igniter (P/N

GP-

122435-S

1. Using a spark gap feeler gauge, check to ensure that the igniter is gapped at 1/8".

2. Prior to installation, a high-temperature anti-seize compound

must

be applied to the

igniter threads.

3. Reinstall the igniter in the location shown in Figure 9. Do not over-tighten. A slight

snugging up is sufficient.

4. Reconnect the igniter cable.

Содержание AERCO 58015-04





















Результаты поиска

Содержание AERCO 58015-04

Отзывы:

Похожие инструкции для AERCO 58015-04

Бренды по названию

Популярные бренды

Watts AERCO 58015-04, Технические инструкции

Результаты поиска

Содержание AERCO 58015-04

Отзывы:

Похожие инструкции для AERCO 58015-04

Бренды по названию

Популярные бренды