manualshive.com logo in svg

WattNode WNC-3Y-208-MB, Инструкция по установке и эксплуатации

Поделиться
Скачать
WattNode WNC-3Y-208-MB Скачать руководство пользователя страница 15

 Installation 15

voltage between each phase and ground. If you see a reading between 0 and 5 Vac, that leg is 
probably grounded (sometimes called a “grounded delta”).

The WattNode meter will correctly measure services with a grounded leg, but the measured 
voltage and power for the grounded phase will be zero and the status LED will not light for 
whichever phase is grounded, because the voltage is near zero. Also, one or both of the active 
(non-grounded) phases may show yellow or red/yellow LED flashing because the grounded leg 
configuration can result in unusual measured power factors for delta services.

For optimum accuracy with a grounded leg, you should also connect the 

N

 (neutral) terminal 

on the meter to the ground terminal; this will not cause any ground current to flow because the 
neutral terminal is not used to power the meter. If you have a grounded leg configuration, you can 
save money by removing the CT for the grounded phase, since all the power will be measured on 
the non-grounded phases. We recommend putting the grounded leg on the 

Ø

B

 or 

Ø

C

 inputs and 

attaching a note to the meter indicating this configuration for future reference.

Mounting

Protect the WattNode meter from moisture, direct sunlight, high temperatures, and conductive 
pollution (salt spray, metal dust, etc.) If moisture or conductive pollution may be present, use an 
IP 66 or NEMA 4 rated enclosure to protect the meter. Due to its exposed screw terminals, the 
meter must be installed in an electrical service panel, an enclosure, or an electrical room. The 
meter may be installed in any orientation, directly to a wall of an electrical panel or junction box.

127 mm (5.0")

143 mm (5.63")

8

5

.6 m

m (

3

.3

7

")

38 mm (1.50") High

Ø

 9.8mm (0.386")

Ø 

5.1mm (0.200")

Drawn to Scale

Figure 7: WattNode Meter Dimensions

The WattNode meter has two mounting holes spaced 127 mm (5.0 in) apart (center to center). 
These mounting holes are normally obscured by the detachable screw terminals. Remove the 
screw terminals by pulling outward while rocking from end to end. The meter or 

Figure 7

 may be 

used as a template to mark mounting hole positions, but 

do not drill the holes with the meter in 

the mounting position

 because the drill may damage the connectors and leave drill shavings in 

the connectors.

You may mount the meter with the supplied #8 self-tapping sheet metal screws using 1/8” pilot 

Содержание WNC-3Y-208-MB































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды