manualshive.com logo in svg

Watson-Marlow BREDEL 701 Series, Руководство пользователя

Поделиться
Скачать
Watson-Marlow BREDEL 701 Series Скачать руководство пользователя страница 10

Replacing the V-belt  

Unscrew the socket head screws and remove the cover with the entire speed control 
mechanism.  

Remove the V-belt.  

Wrap the new V-belt around the open adjustable pulley and let it slip over the spring 
loaded pulley. The V-belt can be easily attached if the adjustable pulley is opened. 
Ensure that the adjustable pulley is opened carefully.  

Replace the removed cover with the complete speed control mechanism and re-
assemble.  

When positioning the top (adjustable pulley closed) speed limiting lock nut, ensure that 
the adjustable pulley has a gap of 0.5-1.0mm to prevent damage to the pulley and motor 
bearings.  

The V-belt should not be in contact with the bottom of the adjustable pulley.  

11 701PB Air motors 

Installation  

A silencer is installed on the air motor’s exhaust port. Install a moisture trap and filter in 
the air line ahead of the motor. If condensates need to be flushed out of the motor, use 
clean, dry air at low pressure. For efficiency of output and speed control, use air lines of the 
same size or next pipe size larger than the intake port of the motor. A 4-way valve which 
can be connected by piping to both air ports of the motor will make reversing possible. Use 
a pressure regulator or a simple shut off valve to obtain desired power and conserve air to 
regulate speed and torque.  

The air motor is designed for air only. Do not allow corrosive, flammable 
or explosive gases or particulate material to enter the motor. Water 
vapour, oil-based contaminants, or other liquids must be filtered out. The 
recommended air pressure should not exceed 7 bar (100 PSIG) 
maximum. 

Always disconnect the air supply before servicing.

 

Ensure that the air motor is correctly installed and lubricated in 
accordance with the guidelines in this operating instruction. Each air 
motor is fitted with an outlet port restrictor to stop the motor running 
faster than the maximum designated speed. Failure to observe correct 
installation and lubrication procedures with air motors will cause damage 
that will invalidate your warranty. 

Page 10 of 25

Watson-Marlow Bredel E-Manuals

14/12/2009

file://M:\staging\pdfs-global\m-701baseplate-gb-02.htm

Содержание BREDEL 701 Series


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды