Watson Marlow Pumps 500 Series Скачать руководство пользователя страница 4

Страница: 4 / 157

1.1

Declaration of conformity

Watson-Marlow Limited

Falmouth

Cornwall

TR11 4RU

England

530 Cased pumps (Models: S, SN, U, UN, Du, DuN, Bp, BpN

, En, EnN

, Pn, PnN

)

630 Cased pumps (Models: S, SN, U, UN, Du, DuN, Bp, BpN

, En, EnN

, Pn, PnN

)

730 Cased pumps (Models: SN, UN, DuN, BpN

EnN

, PnN

)

Manufacturer:

Watson Marlow Ltd

Bickland Water Road

Falmouth

TR11 4RU

This declaration of conformity is issued under the sole responsibility of the manufacturer

All models and versions of the 530

, 630 and 730

series of cased peristaltic pump with all

approved pump

heads, tubing and accessories.

The object of the declaration described above is in conformity with the relevant Union

harmonisation legislation:

Machinery Directive 2006/42/EC

EMC Directive 2014/30/EC

ROHS Directive 20

863

Harmonised standards used:

BS EN61010-1:2010 third edition Safety requirements for electrical equipment for

measurement, control, and laboratory use Part 1: General requirements

EN61326-1:2013 Electrical equipment for measurement, control and laboratory use – EMC

requirements Part 1: General requirements

BS EN 60529:1992+A2:2013 Degrees of protection provided by enclosures (IP code)

ntertek Testing and Certification Ltd, No: 3272281, performed compliance testing to UL

61010-1:2012 and CSA C22.2#61010-1-12:2012 and issued certification of compliance to

these standards.

Signed for and behalf of:

Watson Marlow Ltd

Falmouth,

December

Simon Nicholson, Managing Director, Watson-Marlow Limited

EC Declaration of Conformity

m-530pn-en-09 02-02-22

Содержание 500 Series






























































































































































Результаты поиска

Содержание 500 Series

Отзывы:

Похожие инструкции для 500 Series

Бренды по названию

Популярные бренды

Watson Marlow Pumps 500 Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 500 Series

Отзывы:

Похожие инструкции для 500 Series

Бренды по названию

Популярные бренды