Watson Marlow Pumps 500 Series Скачать руководство пользователя страница 88

Страница: 88 / 157

Table 13 - Pump Control

ADI

Name

Access

Type

Description

Set pump

speed

(deciRPM)

Write

UInt16

Speed is set in Deci RPM. Max speed depends on head
type. See Pump Head enumeration table

Set pump

speed limit

(deciRPM)

Write

UInt16

Speed is set in Deci RPM. Max speed depends on head
type. See Pump Head enumeration table

Set failsafe

speed

(deciRPM)

Write

UInt16

If the failsafe is enabled the pump will run continuously
at the selected speed in the event of a communications
loss.

101

Control

bitfield

Write

UInt16

Bit 0

Set fail safe enable, Enabled the failsafe
speed. If disabled the pump will stop in the
event of a communications loss. If enabled
the pump will run at the speed set in the
“SetFailsafeSpeed” parameter

Bit 1

Set pump direction to anti-clockwise, If set
the pump will run anti-clockwise. Pump
defaults to clockwise rotation

Bit 2

Start pump, Set to 1 (true) to allow the
pump to run. 0 will stop the pump. Note
that pump enable needs to be set

Bit 3

Enable pump, Need to set to 1 to allow
pump to run. Setting to 0 will stop the
pump and not allow the pump to run.

Bit 4

Reset pump run hours to zero, Resets the
run hours accumulator

Bit 5

Pause flow totaliser, Set to 1 to pause the
internal Total volume pumped parameter.
Setting to 0 will un-pause the parameter

Bit 6

Reset flow totaliser to zero, Set to 1 to reset
the Total volume pumped to 0. Set to 0 to
allow the Total volume pumped to
accumulate

Bit 7

Reset revolution count to zero, Set to 1 to
reset the Pump head revolution count to 0.
Set to 0 to allow the Pump head revolution
count to increment.

m-530pn-en-09 02-02-22

Содержание 500 Series






























































































































































Результаты поиска

Содержание 500 Series

Отзывы:

Похожие инструкции для 500 Series

Бренды по названию

Популярные бренды

Watson Marlow Pumps 500 Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 500 Series

Отзывы:

Похожие инструкции для 500 Series

Бренды по названию

Популярные бренды