Watkins HOT SPOT RE Скачать руководство пользователя | Manualshive

Страница: 6 / 36

background image

x

Page x

Safety Information

Page 4

WARNING:

The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia in hot tubs and spas.

TO REDUCE THE RISK OF INJURY:

• The water in the spa should never exceed 104°F. Water temperatures between 100°F and 104°F are considered

safe for a healthy adult. Lower water temperatures are recommended for extended use (exceeding 10 minutes)
and for young children. Extended use can cause hyperthermia.

• Pregnant or possibly pregnant women should limit spa water temperatures to 100°F. Failure to do so may result in

permanent injury to your baby.

AVOIDING THE RISK OF SKIN BURNS:
WARNING:

• To reduce the risk of injury, before entering a spa the user should measure the water temperature with an accurate

thermometer, since the tolerance of temperature-regulating devices may vary by as much as ±5°F.

• Test the water with your hand before entering the spa to be sure it’s comfortable.

SAFETY SIGN

Each Hot Spot

®

Spa is shipped with a SAFETY SIGN in the owner’s package. The sign, which is required as a condition of

Product Listing, should be permanently installed where it is visible to the users of the spa. To obtain additional SAFETY
SIGNS, contact your Hot Spot

®

Spa Dealer and request Part #70798.

IMPORTANT SPA INSTRUCTIONS

The following contains important spa information, and we strongly encourage you to read and apply them.

DO:

• Use and lock the cover when the spa is not in use, whether it is empty or full.
• Follow the Spa Care and Maintenance recommendations stated in this manual.
• Use only approved accessories and recommended spa chemicals and cleaners.

DON’T:

• Leave the Hot Spot

®

Spa exposed to the sun without water or the cover in place. Exposure to direct sunlight can

cause solar distress of the shell material.

• Roll or slide the spa on its side. This will damage the siding.
• Lift or drag the cover by using the tie-down straps; always lift or carry the cover by using the handles.
• Attempt to open the electrical control box. There are no user serviceable parts inside. Opening of the control box

by the spa owner will void the warranty. If you have an operational problem, carefully go through the steps outlined
in the Troubleshooting section. If you are not able to resolve the problem, contact your authorized Hot Spot® Spa
Dealer. Many problems can easily be diagnosed over the telephone by an Authorized Service Technician.

SAVE THESE INSTRUCTIONS

«
...
4
5
6
7
8
...
»

Содержание HOT SPOT RE





































Отзывы:

Нет отзывов

Похожие инструкции для HOT SPOT RE

Бренд: Riptide Страницы: 22

Бренд: Aber Hot Tub Manufacturing Страницы: 58

Бренд: Jacuzzi Страницы: 28

PowerActive Swim Spa Series

Бренд: Jacuzzi Страницы: 28

MILLENNIUM 9 AI9mIl7700

Бренд: Aquatic Страницы: 1

Бренд: Teuco Страницы: 10

Clever Spa Paradiso

Бренд: Clever Страницы: 16

Бренд: EAGO Страницы: 9

Бренд: BullFrog Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды