Watkins HOT SPOT RE Скачать руководство пользователя | Manualshive

Страница: 34 / 36

background image

Service Information

Page 32

ACTS INVALIDATING WARRANTY

The limited warranty is void if the Hot Spot

®

Spa has been subjected to alteration, misuse or abuse, or if any repairs on the spa are attempted by

anyone other than an authorized representative of Watkins Manufacturing Corporation. Alteration is defined as any component or plumbing
change, electrical conversion, or the addition of any non-approved sanitation or water purification device or heating system which contributes to a
component failure, unit failure or unsafe operating condition. Misuse and abuse shall include any operation of the spa other than in accordance
with Watkins Manufacturing Corporation printed instructions, or use of the spa in an application for which it is not designed; specifically: use of the
spa in a non-residential application; damage caused by operation of the spa at water temperatures outside the range of 32°F and 120 °F; damage
caused by a dirty, clogged or calcified filter cartridge; damage to the spa surface caused by the use of Tri-Chloro chlorine, chemical tablets, acid,
or any other spa sanitizing chemicals or spa surface cleaners which are not recommended by Watkins Manufacturing Corporation; damage
caused by allowing undissolved spa sanitizing chemicals to lie on the spa surface (no spa surface material can withstand this kind of abuse);
damage to components or spa surface caused by improper pH balance or other improper water chemistry maintenance; and damage to the spa
surface caused by leaving the spa uncovered while empty of water and in direct exposure to sunlight (this may cause solar heating distress in
warm weather regions). These are considered abuses and may invalidate this warranty.

DISCLAIMERS

Watkins Manufacturing Corporation shall not be liable for loss of use of the Hot Spot

®

Spa or other incidental or consequential costs, expenses or

damages, which may include but are not limited to, the removal of a permanent deck or other custom fixture. Any implied warranty shall have a
duration equal to the duration of the applicable warranty stated above. Under no circumstances shall Watkins Manufacturing Corporation or any of
its representatives be held liable for injury to any person or damage to any property, however arising.

WATKINS CUSTOMER SERVICE

If you have any questions about any aspect of your Hot Spot

®

Spa set-up, operation or maintenance that have not been answered by this manual,

consult your Hot Spot

®

Spa Dealer.

Watkins Manufacturing Corporation can be reached at: 800-999-4688 (Extension 432), Monday through Friday, 8 am to 5 pm Pacific Standard
Time (PST), or e-mail at [email protected].

«
...
32
33
34
35
36
»

Содержание HOT SPOT RE





































Отзывы:

Нет отзывов

Похожие инструкции для HOT SPOT RE

Бренд: Dreamline Страницы: 8

Бренд: Canadian Spa Страницы: 14

Бренд: Canadian Spa Страницы: 24

Бренд: Tadpole Страницы: 31

PLATINUM Series

Бренд: Calspas Страницы: 36

Бренд: Jacuzzi Страницы: 48

Бренд: spaxo Страницы: 13

Бренд: SpaVida Страницы: 20

Бренд: Intex Страницы: 2

PureSpa Greystone Deluxe Square

Бренд: Intex Страницы: 22

Бренд: Intex Страницы: 24

PureSpa Greywood Deluxe SB-HWF20

Бренд: Intex Страницы: 32

Бренд: Floataway Страницы: 38

AiriSpa DS1oval110v

Бренд: Comfort Страницы: 20

Бренд: mychway Страницы: 14

Бренд: EAGO Страницы: 9

Бренд: BullFrog Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды