Watkins Wellness HotSpring Hot Spot Relay, Руководство пользователя

Страница: 28 / 36

Page 25
Electrical Requirements
115-230 VOLT CONVERSION
( PACE & STRIDE MODELS)
Refer to the following instructions to convert your 115 volt PACE & STRIDE spa to a 230 volt 30A or 50A spa. Use wiring diagram below
NOTE : Converting the spa to 230 volts operation should only be done by an authorized service agent or a qualified electrician. The heater will run at 4K and
the jet pump will not run concurrent on high speed with heater @ 30A and will run concurrent with heater @ 50A. When using a 50A service a Low Level
change is required. Press and hold the JETS button for 30 seconds to access the Low Level settings on the control panel. Use the +/- button to change
the setting from LL3 Factory Default (non concurrent heat and high speed) to LL4 (concurrent Heat and High Speed pump) configuration. Press the LIGHT
button within 25 seconds to save the new program.
The conversion requires a subpanel (230 volt) which may be purchased from your Authorized
dealer.
1. Disconnect the power cord from the house receptacle.
2. Remove the screws and open the equipment compartment door.
3. Remove the screws from the control box.
4. Open the control box cover.
5. Remove the power cord wires, and the power jumper wire (from line 2 and neutral) on the
line side of the terminal block.
A licensed electrician must install the subpanel (available from your dealer) to supply power to
the spa. The subpanel must be placed in sight of the spa at a minimum distance of 5 feet (1.5
m) away. All electrical connections must be made in accordance with the wiring information
contained in this manual and on the back of the field wiring access panel of the control box.
NOTE: Bond the spa to all exposed metal equipment or fixtures, handrails, and concrete pad per N.E.C. and all local codes.
230 VOLT 30A OR 50A WIRING INSTRUCTIONS
( RELAY & RHYTHM MODELS)
NOTE : The subpanel must be placed within 100 feet (30 m) of the main electrical service panel, and between 5 feet (1.5 m) and 50 feet (15 m) away from
the spa. All electrical connections must be made in accordance with the wiring information contained in this manual and on the back of the field wiring
access panel of the control box. When using a 30A configuration, a HOT SPRING Spa Technician must reconfigure spa to LL3 to run heater at 4K but Not
run concurrent while both jet pumps are on. Press and hold the JETS 1 button for 30 seconds to access the Low Level settings on the control panel. Use the
+/- button to change the setting to LL3. Press the LIGHT button within 25 seconds to save the new program.
HOT SPRING spas must be wired in accordance with all applicable local electrical codes. All electrical work should be done by an experienced, licensed
electrician. We recommend the use of appropriate electrical conduit, fittings, and wire for all circuits.
30/50A
30/50A
L2
N
L1
L1
N
G
L2
*ALL CANADIAN SPA MODELS USE #8 AWG GREEN, GROUND.
THESE SPAS ARE INTENDED FOR USE WITH GFCI SUBPANEL
PROVIDED.
T h e e x a c t p h y s i c a l l o c a t i o n o f t h e t e r m i n a l s o n t h e G F C I b r e a k e r
w i l l v a r y b e t w e e n m a n u f a c t u r e r s . C o n n e c t i n g t h e h o t w i r e t o t h e
n e u t r a l t e r m i n a l w i l l c a u s e i r r e v e r s i b l e d a m a g e t o t h e c o n t r o l b o x .
230VAC, 50 Amp
2-POLE
CIRCUIT BREAKER
(NON GFCI)
MAIN SERVICE
ELECTRICAL
PANEL
230VAC, 30/50A, MODELS
SUBPANEL
WITH GFCI
BREAKERS
MORE THAN 5' (1.5 m)
THE SUBPANEL MUST BE
WITHIN SIGHT OF THE SPA
DO NOT EXCEED 50' ( 15 m)
CONTROL BOX
W A R N I N G !
#8 AWG WHITE, NEUTRAL
#8 AWG GREEN, GROUND
#8 AWG BLACK, L1
#8 AWG RED, L2
N, NEUTRAL, #8 AWG WHITE
L2, HOT, #8 AWG RED
L1, HOT, #8 AWG BLACK
GROUND, #10 AWG GREEN*
GRD
LESS THAN 100' (30 m)
L1
N
G
L1
N
G
L2
See Wiring
Illustration
below
230 VAC Wiring
(Converted)
Power Jumper must be
remove to operate 230 VAC
Spa Models
English French Spanish