Waterway CLEARWATER II, Руководство пользователя

Страница: 3 / 4

1 2
3
7
7 6
4
8
9
11
5
10
12
13
14
15
17
16
18
19
20
21 22
23
21
24a (2)
24
29
28
30
31
21
22
33
32
27
28
26
21
25
Our ClearWater II D.E. Filter System is shipped from Waterway complete
with everything you need right in the box. Assemble filter system only
after above-ground pool is installed. Fill pool with water. Do not raise
water level above pool return line.
The pool equipment should be located between pool skimmer and
return line. The filtration system should not be closer than 2 ft. and not
further than 5 ft. from the pool. The ClearWater II D.E. Filter System
needs to be on a completely flat surface (e.g. patio block, cement slab,
etc.). The pump will require a 110 volt/20 amp service.
WARNING: A GFCI is required. Follow national and local
building and safety codes.
Before opening shipping carton, make sure box is in the upright
position. Inside the carton, you will find:
1. One base
2. One pump (packaged in separate box)
3. One filter
4. Two lengths of 6 ft. hose
5. One bag with fittings
WARNING! READ ALL INSTRUCTIONS AND WARNING
LABELS BEFORE OPERATING FILTER!
1. Place filter and base on a level, secure surface. Place the pump on
the base to the left of the filter. The pump should now be facing the
filter marked “Inlet”. There is no need to disassemble filter or pump
assemblies.
2. Open pump trap lid and remove 2" gasket. Place 2" gasket into union
nut. Hand tighten union nut to suction side of pump (Detail 5).
3. Secure pump to the base using the pin & anchor assemblies
(Detail 4).
4. Open fittings bag and remove coupling assembly (Detail 2).
Assemble 2" gasket, coupling, coupling O-Ring, and 2" union nut,
and thread into inlet side of filter.
5. Thread 2" union nut to pump discharge (Detail 3). Thread hose
adapter with O-Ring, to pump trap suction side (Detail 1).
6. From the fittings package, remove 11/2" hose adapter and O-ring
(Detail 2, #21 & 22). Thread into the outlet side of the filter tank.
7. Remove 4 hose clamps from the fittings bag. Select one of the hose
lengths and slip one clamp over the end of hose adapter. Place the
end of the hose on to the hose adapter (pump suction) and the other
end to the hose adapter end of the pool skimmer. Repeat steps with
filter outlet to pool return.
8. Remove the Lid Handle, #1, from the fittings bag and attach it to
the top of the Lid Assembly, #12, as shown (Detail 6). Secure
ClearWater Filter to ClearWater Filter Base using #24a Phillips Head
Screws (2) (Detail 6a & 6aa). Fill pool until water level is halfway up
length of skimmer throat.
9. Open air release knob. Plug in and turn on pump. Air will pass out
of the filter through the air release knob. Once water discharges from
knob, close it.
NOTE
: To remove Lid Assembly, take off Filter Nut, #3, insert Filter
Wrench, #20a, in notch between Filter Body, #20 and Lid Assembly,
#12, twist and separate as shown in Detail 6a.
CLEARWATER II D.E. FILTER SYSTEM OWNER’S MANUAL CLEARWATER II D.E. FILTER SYSTEM REPLACEMENT PARTS
INSTALLATION INSTRUCTIONS
Item Part No. Description
1 519-7601 Lid Handle
2 819-9002 #12 x 3/4" S/S Phillips Head Screw
3 718-7251 Filter Locknut Assembly
4 602-0200 Air Relief Plug
5 805-0207 O-Ring - Air Relief
6 830-4000SS Pressure Gauge
7 519-7451 Handle Assembly (2)
8 805-0224 O-Ring - Air Relief
9 519-7430 Gauge - Fitting Adapter
10 805-0117SD O-Ring - Adapter
11 805-0460 Lid O-Ring
12 519-7411 Lid Assembly (Small)
519-7401 Lid Assembly (Large)
13 519-7441 Wing-Nut
14 500-7310 Screen/Sock Assembly
15 718-7210 Tie Nut - D.E.
16 419-7241 Plug - 2" x 1 1/2" MPT
17 519-7269 Locator - Top Grids - D.E.
18 550-7210 D.E. Grids - 12 sq. ft. (7)
550-7220 D.E. Grids - 18 sq. ft. (7)
19 550-7100 Base Assembly - 12 sq. ft.
550-7120 Base Assembly - 18 sq. ft.
20 515-7251 Filter Body Bottom
20a 519-7470 Filter Wrench (see Detail 6a)
21 805-0224 O-Ring (4)
22 417-6241 1 1/2" MPT x 1 1/2" Male Smooth
Hose Adapter (2)
23 500-5300 Drain Assembly
24 672-7401 ClearWater II Base
24a 819-0044 #10 x 1" S/S Phillips Head Screw (2)
25 415-5001 2" Union Nut
26 419-7241 Coupling
27 711-4010 2" Union Gasket (2)
28 429-7221 Snap Pin (4)
29 PH1100 1 HP - 1-Speed Hi-Flo Pump
PH1150 1 1/2 HP - 1-Speed Hi-Flo Pump
PH1200 2 HP - 1-Speed Hi-Flo Pump
PH2100 1 HP - 2-Speed Hi-Flo Pump
PH2150 1 1/2 HP - 2-Speed Hi-Flo Pump
PH2200 2 HP - 2-Speed Hi-Flo Pump
30 310-6500 6" Trap - 1 1/2" Buttress x 2" Flange
31 319-3230 6" Basket Assembly
32 805-0436 O-Ring
33 319-3260 6" Trap Lid
DETAIL 1 DETAIL 2 DETAIL 3
DETAIL 4 DETAIL 6aa
DETAIL 5
DETAIL 6a
DETAIL 6
33
32
22
21
31
30
20
27 26
21
25
21
21 22
23
27
26
21
25
29
28
28
22
21
31
30
29
27
32
33
1
2
3
12
20
20a
24a
24a
24a