CERTIFIED WATER FILTER SYSTEM
IMPORTANT
DO NOT USE extra lubricants, unapproved sealants and tools to tighten hand tightened
only parts. Use of tools other than hand tighten only parts voids warranty. Testing was
performed under standard laboratory conditions; actual performance may vary. Flush
the system and change the filter as suggested. The contaminants or other substances
removed or reduced by this water filter are not necessarily in all users’ water.
PERFORMANCE
Performance claims are based on independent lab results and manufacturer’s internal
test data*. Actual performance is dependent on influent water quality, flow rates,
system design and applications. Your results may vary. Performance claims are based
on a complete system, including a filter, housing, and connection to a pressurized
water source. This filter must be operated according to the system’s specifications
in order to deliver the claimed performance. It is essential to follow operational,
maintenance, and filter replacement requirements, as directed for each application, for
this filter and system to perform correctly. Read the Manufacturer’s Performance Data
Sheet accompanying the system and change the filter as suggested. The contaminants
or other substances removed or reduced by this water filter are not necessarily in all
users’ water.
This system has been tested for the reduction of the substances listed below. The
concentration of the indicated substances in water entering the system was reduced
to a concentration less than equal to the permissible limit for water leaving the system,
as specified in NSF/ANSI 53. Minimum substance reductions are as follows:
SUBSTANCE
INFLUENT CHALLENGE
CONCENTRATION (MG/L)
MAXIMUM PERMISSIBLE
PRODUCT WATER
CONCENTRATION (MG/L)
NSF/ANSI
STANDARD
Lead
0.15 +/- 10%
0.01
53
Cyst
minimum 50,000/L
99.95%
53
PFOA/PFOS
1.5 +/- 10%
0.07
53
v
NAME AND
PART NUMBER
SIZE &
MICRON
RATING
RATED CAPACITY & FLOW RATE
PEAK FLOW &
% REDUCTION OF LEAD
CHLORINE/CHLORAMINE
TASTE AND ODOR REDUCTION CAPACITY (*)
PRESSURE DROP
SPEC
Infinity Protector
INF-PRO1
8” x 40” 0.5
Lead Reduction and PFOA/PFOS
100,000 gallons @ 4.51 GPM (378,541
Liters @ 17.1 lpm)
@ 99.62% lead reduction
@ 97.9% PFOA/PFOS reduction
8 GPM (30.2lpm) @
99.62% reduction
(*) >88,000 gallons at 8 GPM
(333,116 Liters @ 30.2lpm)
>300,000 gallons @ 15 GPM
(1,135,533 Liters @ 56.8 lpm) with greater than
90% reduction, estimated capacity using 2ppm of
free chlorine.
>150,000 gallons @ 8 GPM
(567,812 Liters @ 30.3 lpm) with greater
than 85% reduction, estmated using 3ppm
of chloramine.
9 psid
@ 4.51 GPM
REPLACEMENT CARTRIDGE FILTERS ARE LISTED AS Infinity Protector 0.5 Micron High Capacity Carbon Block // PART NUMBER:
INF-PRO1-FX
*Claims are not performance tested by IAPMO or NSF. Performance claims are based on independent laboratory and manufacturer’s internal test data.
Actual performance is dependent on influent water quality, flow rates, system design and application. Results may vary.
This system is certified by IAPMO R&T against
NSF/ANSI Standards 53 (also CSA B483.1)
for the reduction of claims specified on the
performance data sheet.
This pressure vessel is tested and certified
by NSF International against NSF/ANSI
Standard 44 and 61 for materials and
structural integrity requirements
Electrical Requirements: Grounded & Unswitched 115 V outlet and 3-AAA Batteries
Filter Replacement Operating Instructions: New cartridges must be flushed for a
minimum of 10 minutes prior to use. System and installation to comply with state and
local laws and regulations. Do not use with water that is microbiologically unsafe or
unknown quality without adequate disinfection before or after the system. Systems
certified for cyst reduction may be used on disinfected waters that may contain
filterable cysts. Manufactured from NSF/ANSI standard 61 and California Prop 65
Compliant certified coconut shell carbon and raw materials.
SPECIFICATIONS
