Waters 2707 Скачать руководство пользователя страница 65

Страница: 65 / 100

Replacing syringe plungers and plunger tips

3-15

Remove the Teflon syringe gasket from the valve’s syringe fitting port.

Fill the new syringe with degassed wash solvent.

Recommendations:

•

Use isopropanol as the wash solvent.

•

Remove air bubbles from the syringe.

Fit a new Teflon gasket on the syringe.

Tip:

The syringe includes a Teflon syringe gasket.

Connect the plunger of the filled syringe to the syringe drive by pushing
it straight onto the clip.

Requirement:

Keep the top threaded end below the syringe valve.

Raise the syringe, and screw it firmly into the connector.

In the Replace Sample Syringe window, click Reset.

Result:

The syringe moves to the home position and dispenses its

contents to waste.

10. Using the Control menu of the 2707 Console, perform a standard wash

routine.

Result:

All tubing connected to the syringe valve refills and flushes.

11. Purge all air bubbles from the syringe and buffer tubing by repeatedly

washing the needle or removing and repriming the syringe with
degassed, nonaqueous organic solvent.

Replacing syringe plungers and plunger tips

To replace the plunger or plunger tip

From the Maintain menu of the 2707 Console, click Replace > Syringe.

Result:

The syringe plunger lowers.

Unscrew the syringe from syringe valve.

Requirement:

Keep the connector in the valve intact.

Caution:

To avoid valve damage, do not use a sharp tool for gasket

removal.

Содержание 2707




































































































Результаты поиска

Содержание 2707

Отзывы:

Бренды по названию

Популярные бренды

Waters 2707, Руководство оператора

Результаты поиска

Содержание 2707

Отзывы:

Бренды по названию

Популярные бренды