Waterous Aquis Foam Manager Скачать руководство пользователя страница 4

F

1031, Section 2414

Page 4 of 8

System Components

Table 1. System Components

Ref. No.

Description

1

Aquis

t

 Foam Pump (Proportioner)

2

Foam Pump Inject Valve

3

In

line Foam Concentrate Strainer

Ref. No.

Description

4

Aquis

t

 Foam Pump OIT (Control Panel)

5

Aquis

t

 Operation Instruction Panel Plate

6

OIT Cable

Figure 1. System Components

1

2

4

3

To Foam Tank

5

3

6

Items Shipped Loose

with Aquis Foam Pump

IL3436

Optional Items from Waterous

Description

Foam Tank Level Switch

Aquis Rating Panel Plate

Aquis System Schematic Panel Plate

OIT (Control Panel) Extension Cable

Operation

A pumper equipped with a Foam Manager

t

 foam unit can

be operated in water only and/or foam modes. It is pos­

sible to pump water from one discharge and foam solution
from another discharge.

Water Only Operations

All unit operations begin with pumping water. See the fol­
lowing instruction for details on how to operate and pump
water from your Waterous fire pump:

·

F-1031, Section 2114, 

Operation and Maintenance

Instructions for Waterous CMU Series Centrifugal Fire
Pumps

or

·

F

1031, Section 2115, 

Operation and Maintenance

Instructions for Waterous CS and CSU Series Centrif-
ugal Fire Pumps

CAUTION

Overheating hazard. 

May cause damage to the pump.

Running the unit without adequate water flow or an

overheated water supply can cause damage to the

pump.

Содержание Aquis Foam Manager









Отзывы: