background image

 

WL400 

Manual                                                                                                                                    Page 52 – Revision: 7‐16‐2018 

 

17.

 

On Back of Cabinet, connect two pieces of tubing to the RO Drain and 
Water Out line and run to external drain.

 

 

 
 
 
 

18.

 

Connect power cord to 

WL400

 

Water Treatment System

 and turn on Red Power Switch. 

 

19.

 

Connect power to 

WL400 Water Treatment System

.  Turn on Red Power 

Switch 

I=ON

.    DO NOT TURN ON THE GREEN HEATER/COMPRESSOR 

SWITCH 

 

CAUTION!  

NEVER TURN ON HEATER BEFORE FILLING HOT TANK.

 

 

Green Heater/Compressor Switch must be in the O=OFF position while 
the hot tank is empty.  Damage could occur within one minute and the overloads (high limit) 
will require manual reset if heater is turned on with an empty hot tank.  

 

20.

 

Connect supply water to Water In Fitting on back of cabinet.  Turn on water supply and flush RO 
system to drain for 4 hours.  Water should be draining from both Water Out line and the Drain 
Line. 

 

21.

 

After 4 hours of flushing, turn Off Incoming Water.  Connect water line from the Base Cabinet to 
Water In fitting on 

WL400 Water Treatment System

 

22.

 

Open Bladder Tank and turn on supply water. 

 

23.

 

Allow Bladder Tank to fill for 1 hour. 

 

24.

 

Fill Hot Tank for approximately 1 minute.  Depress both the “Hot” and “Extra Hot” buttons to 
dispense.  Red light should illuminate above the dispensing area after a 2 second delay. 

 

25.

 

Fill cold tank for approximately 2 minutes.  The Blue Light should 
illuminate above dispensing area.  

 

 
 
 
 
 
 

 

26.

 

Turn on Green Heater/Compressor Switch.

 

 

 

Fill the Hot Tank 
 

27.

 

Press the Hot Water Select Button, followed by the main dispensing button to fill the hot tank.  
Water will dispense from the faucet once the hot tank is full.  Flush until water is clear. 

 

Содержание WL400 Series















Отзывы: