background image

 

WL400 

Manual                                                                                                                                    Page 62 – Revision: 7‐16‐2018 

Green Heater/Compressor Switch must be in the O=OFF position while the hot tank is empty.  
Damage could occur within one minute and the overloads (high limit) will require manual 
reset if heater is turned on with an empty hot tank.  
 

 

11.

 

Connect supply water to water in fitting on back of cabinet.  Turn on the Water Supply and flush 
RO system to drain for 4 hours.  Water should be draining from both Water Out Line and Drain 
Lines. 
 

12.

 

After 4 hours, turn off Incoming Water.  Connect Water Out Line from Base Cabinet to drain 
water in fitting on 

WL400

 

Water Treatment System.

 

 

13.

 

Open Bladder Tank and turn on supply water. 

 

14.

 

Allow bladder tank to fill for 1 hour. 

 

15.

 

Fill Hot Tank (Approximately 1 minute).  Depress both Hot and Extra Hot Buttons to dispense.  
Red light should illuminate above dispensing area after 2 second delay.

 

 

 

 

 

16.

 

Fill Cold Tank (Approximately 2 minutes).  Blue light should illuminate 
above dispensing area. 

 

 
 

 

17.

 

Turn on Green Heater/Compressor Switch. 

I=ON

.

 

 

 

 

 

 

 

 

 

 

 

Содержание WL400 Series















Отзывы: