WaterLogic CUBE FIREWALL Скачать руководство пользователя

Страница: 81 / 85

CUBE

Manual

Page 81 - Revision: 5-24-2017

HOT WATER TROUBLESHOOTING

Hot Water is not Hot 187°F (86C°)

Hot Water is not Available

Resetting Hot Tank Overload and Programming the DIP Set-Up for Hot Water

Temperature Instructions are included in this Troubleshooting section.

1. Hot Water is not Hot 187°F (86°C) +/- 5°F

Possible Reason

Solution

No power to Hot Tank

Check that the Green Heater and

Compressor switch is on.

Turn Green Heater and Compressor Switch

on. I = ON

Tank has run out of Hot Water.

Hot Tank Capacity is 1.3 liters.

Wait for Hot Tank to heat water to temperature prior to

dispensing more hot water.

Greater Water Capacity Waterlogic Water Systems are

available.

Hot Water Temperature

Programming

Verify that the CUBE has been programmed to desired

temperature. See Programming: Hot Water Temperature DIP

Set-Up Instructions in this Troubleshooting Section.

2. Hot Water is not Available

Possible Reason

Solution

Hot Tank Overload Tripped

Reset Hot Tank Overload.

Hot Tank Overload Instructions in this Troubleshooting

Section.

Содержание CUBE FIREWALL






















































































Результаты поиска

Содержание CUBE FIREWALL

Отзывы:

Похожие инструкции для CUBE FIREWALL

Бренды по названию

Популярные бренды

WaterLogic CUBE FIREWALL, Руководство пользователя

Результаты поиска

Содержание CUBE FIREWALL

Отзывы:

Похожие инструкции для CUBE FIREWALL

Бренды по названию

Популярные бренды