P
remises
© WASP S.r.l.
8
64
USE OF THE PRINTER
8
8.7. Free zeta system
The Free Zeta system is a useful command to resume interrupted prints and for any reason it was not possible to
recover with the Resurrection system.
It is based on the principle of restarting to print a chosen gcode from a certain height onwards, so that the first
layer of the new print adheres to the last printed layer.
Some cases it can serve are when:
•
The Resurrection automatic save was not successful
•
The material is finished but the machine has continued to print
•
The nozzle stopped during printing but the machine has continued to print
The cases in which it is not possible to recover the print are when:
•
The piece has come off the printing floor
•
The piece split during the press
•
The deformation of the piece is such that it is not possible to recover the print
To run the Free Zeta system correctly.
1. Remove any debris on the last layers until the last clean print layer is obtained
2. Bring the machine floor into temperature
3. Select the “Free Zeta system” command from the “PREPARE” menu (fig. 8.7a)
4. Go down with the navigator until the nozzle is extremely close to the last layer of the printed object, just like
when you are verifing the printing bed’ height (fig. 8.7b)
5. Click the “Gcode” button
6. Select the gcode to be recovered and launch the print.
7. Close the machine door
8.8. Set Z max
The printer height is the distance (in mm) set between the nozzle’s tip and the printing bed.
It is a fundamental requirement for calibration. The command can be found inside PREPARE> Set Z max.
It is necessary when it is not possible to perform an Autocalibration and in one of the following cases:
•
Extruder‘s change
•
Cartridge’s change
•
Printing bed Replacement
NOTE:
If the height set is lower than this measure, the tool will work higher than necessary, in that way the material will
not attach properly to the floor.
If the height set is higher than required, the tool will work at a level below the printing bed, with consequent
damage to the printing bed and tools.
Содержание DELTA 4070
