Warren Controls AmurAct Linkage LS Series, Инструкции по установке, эксплуатации и обслуживанию

Страница: 6 / 24

6
2600 Emrick Blvd • Bethlehem, PA 18020 • USA • 800-922-0085 • www.warrencontrols.com AMURACT_IOM_RevK_0415
WIRING SUPPLY, SIGNAL AND FEEDBACK
1 2
TB4
NEUTRAL
LINE
120 Vac
F3 & F4 MOTORS
120 VAC (SINGLE-PHASE 50/60 HZ)
Locate the green case-grounding wire inside the motor case and connect
it to the earth ground lead from the power source. Connect the neutral
(typically white) wire to terminal one (1) on terminal block TB4. Connect
the “hot” (typically black) wire to terminal two (2). This terminal block was
identified as TB5 on earlier builds of these motors.
F5 & F6 MOTORS
220 VAC (SINGLE-PHASE 50/60 HZ)
Locate the green case-grounding wire inside the motor case and connect
it to the earth ground lead from the power source. Connect one “hot” wire
to each of the two terminals on terminal block TB4. This terminal block
was identified as TB5 on earlier builds of these motors.
1 2
TB4
LINE
LINE
220 Vac
EARTH GROUND
1 2
TB1
COMMON (-)
(LINE)
24 VAC OR
30 VDC
3 4 5
F3 & F4 MOTORS
24 VAC OR 30 VDC
(24 VDC - W / Special Considerations)
If the actuator is to be powered by 24 VAC or 30 VDC, connect the nega-
tive or common wire to terminal ONE (1) and the positive (or "hot" wire)
to Terminal TWO (2) on TB1. When powered by (24 VDC, Special Consider-
ation) voltage, motor torque will be reduced by approximately 10% which
will reduce close off capability. Contact the factory for questions.
If the control signal is 4 - 20 mA, connect the control wires to
TB1 as shown. Dipswitch #3 MUST be in the ON position.
EARTH GROUND
IMPORTANT: The AmurAct actuator is precision calibrated at the factory.
Confirm that the control signal at the site is 4-20 mAdc. The control signal
minimum must reach 4.00 mAdc. If the control signal minimum does not
reach 4.00 mAdc, the actuator may not reach its end of travel in that direc-
tion and the valve may not shut-off tightly. The control signal maximum
must reach 20.00 mAdc. If the control signal maixmum does not reach
20.00 mAdc the actuator may not reach its end of travel in that direction
and the valve may not fully open (2-way valve) or shut-off (3-way valve).
Preferred Calibration Accuracy:
+ 2.5 A, (Typ)
1
2
TB1
COMMON (-)
(+) CONTROL 4-20 mA DC
3 4 5
This signal is an output signal and not required for operation. The sole
function is to provide a verified feedback signal. The actuator can be set
to provide a 4-20 mA feedback signal (factory default) or a 2-10 Vdc feed-
back signal. For 4-20 mA feedback dipswitch #4 must be in the OFF po-
sition. For 2-10 Vdc feedback, dipswitch #4 must be in the ON position.
Connect the feedback wires to TB1 as shown. If the actuator is set for CCW
rotation on increasing signal (factory default) and the actuator is at 90º
rotation (facing the motor) the feedback will be 4 mA or 2 Vdc, and at 0º
If the control signal is 2 - 10 Vdc, connect the control wires to
TB1 as shown. Dipswitch #3 MUST be in the OFF position.
IMPORTANT: The AmurAct actuator is precision calibrated at the factory.
Confirm that the control signal at the site is 2-10 Vdc. The control signal
minimum must reach 2.00 Vdc. If the control signal minimum does not
reach 2.00 Vdc, the actuator may not reach its end of travel in that direc-
tion and the valve may not shut-off tightly. The control signal maximum
must reach 10.00 Vdc. If the control signal maixmum does not reach 10.00
Vdc the actuator may not reach its end of travel in that direction and the
valve may not fully open (2-way valve) or shut-off (3-way valve).
Preferred Calibration Accuracy:
+ 1.5 mV, (Typ)
SUPPLY VOLTAGE
CONTROL SIGNAL - Current (milliamp) <DEFAULT>
CONTROL SIGNAL - VOLTAGE
1
2
TB1
COMMON (-)
(+) CONTROL 2-10 VDC
3 4 5
FEEDBACK SIGNAL
1
2
TB1
COMMON (-)
(+) OUTPUT
3 4 5
rotation (facing the motor) the feedback will be 20 mA or 10 Vdc. If
the actuator is set for CW rotation on increasing signal the direction
of the feedback signal will be reversed.