Warn 87722 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 8

Warn 87722 Скачать руководство пользователя страница 7

©2011 Warn Industries, Inc.WARN® and the WARN logo are trademarks of Warn Industries Inc.

7

87731A0

I N S T A L L A T I O N I N S T R U C T I O N S

VI. Optional Winch and Light Installation

(Refer to these tips if winch and /or lights are

added to bumper)

1. WARN winch mounting holes are shown in Figure

10. Pull yellow cable through front hole and blue

cable through rear hole after sliding conduit over top

both cables. 1/4” ID conduit is to be used for RT/

XT25 winches; 3/8” ID conduit is to be used for RT/

XT30 winches.

2. If no winch is mounted on bumper the set of holes,

as shown in Figure 10, can be used to mount a set

of lights on top of bumper. If winch is used, there

are holes on bottom of bumper, as shown in Figure

11, that can be used to mount a set of lights.

RT/XT 25 and 30

winch mount holes

Figure 10

Figure 11

Light mount

holes

Hole for blue

cable

Light mount

holes

Bumper to be used with 2500 and 3000 lb. winches

only. Do not attempt to mount 4000 lb. winch on this

application, vehicle damage and operator injury or

death may result.

WARNING

«
...
5
6
7
8
»

Содержание 87722









Отзывы:

Нет отзывов