6
7
button to adjust the blending speed. The LCD will show the setting
speed and motor speed will change.
/05&5IFTQFFEDBOCFTFUGSPNUP0ODFUIF
Pulse
button is released, the motor will shut off and the blender will to return
to standby mode. The changed pulse speed will be stored in memory to
replace the default speed at 100%.
REPROGRAMMABLE STATIONS
5IFSFBSF1SPHSBN#VUUPOTGPSGPVSSFQSPHSBNNBCMFCFWFSBHFTUBUJPOT
for easy operation and consistent results. The factory-set stations are
programmed as listed below:
Liquid drinks
'SP[FOESJOLT
*DFDSFBNESJOLT
Smoothies
2. To run any of the above preset programs, blender must be in
standby mode.
3. Press desired Program button to start the blender. The motor will run at
the pre-set speed within the preset blending time. The LCD will show time
SFNBJOJOH0ODFUIFCMFOEFSDPVOUTEPXOUPUIFNPUPSXJMMTUPQ
running and the blender will return to standby mode and prompt
13&44"/:#6550/50#-&/%
NOTE:
5PUFSNJOBUFBCMFOEJOHQSPHSBNTJNQMZQSFTT4UBSU4UPQ
button or any of the program buttons. After doing this, the blender will
SFUVSOUPTUBOECZNPEFBOE-$%XJMMQSPNQU13&44"/:#6550/
50#-&/%
REPROGRAMMING BEVERAGE STATIONS
Users can add 4 new programs to meet their needs. A program can
consist of several sections, each with a different speed and running time.
'PSFYBNQMF
can be replaced with a new program that has 3 sections,
as shown below:
Section 1: speed = 75%, time = 30 seconds
Section 2: speed = 100%, time = 20 seconds
Section 3: speed = 50%, time = 20 seconds
The program has the following limitations:
Speed: 15% to 100%
Time: 5 to 90 seconds
5PUBMSVOOJOHUJNFJOBQSPHSBNDBOOPUFYDFFETFDPOETJFTVN
of the Sections cannot be longer than 90 seconds.
NOTE:
The
CVUUPOXJMMBDUBTUIFFOUFSLFZUPQSPDFFEUPOFYUTUFQ
during the reprogramming process.
1. To enter new program, press both Speed Up
and Speed Down
buttons simultaneously while unit is in standby mode. The blender will
enter new programming mode and the LCD will prompt ADD NEW
130(3".
/FYUZPVXJMMOFFEUPTFUWBMVFT1SFTTUIF1SPHSBNCVUUPOZPVXBOU
UPSFQMBDF JF5IF-$%XJMMQSPNQU64&61%08/504&5
SPEED: 25%.
NOTE:
25% is the default speed setting in the reprogramming mode.
3. Press Speed Up
or Speed Down
button to set the speed value.
The increment is 1% (150 RPMs). Press and hold the button to quickly
scroll through speeds. The speed can be set between 15% and 100%.
0ODFSFRVJSFETQFFEJTSFBDIFEQSFTT
button or wait 5 seconds
UPDPOGJSNTFUUJOH5IF-$%XJMMOPXQSPNQU64&61%08/504&5
5*.&
NOTE:
'JWFTFDPOETJTUIFEFGBVMUUJNFTFUUJOHJOUIF
reprogramming mode.
5. Use Speed Up
or Speed Down
button to set the time value (up
UPTFDPOET0ODFUIFTFDPOETJTSFBDIFEQSFTTJOH4QFFE6Q
XJMMOPUJODSFBTFUIFWBMVFBOEUIF-$%XJMMQSPNQU.&.03:-*.*5GPS
2 seconds.
6. Press
button or wait 5 seconds to confirm the setting. When the
CMFOEJOHUJNFJTDPOGJSNFEUIF-$%XJMMQSPNQU4&-&$5"/05)&3
SPEED. Repeat steps 3-5 if additional processing is needed.
NOTE:
When pressing Speed Up
or Speed Down
buttons to set
TQFFEGPSOFYUTFDUJPOUIF-$%XJMMQSPNQU64&61%08/504&5
SPEED: 25%.
7. To save the new program settings, press both Speed Up
and Speed
Down
CVUUPOTTJNVMUBOFPVTMZ5IF-$%XJMMQSPNQU/&8130(3".
130(4"7&%GPSTFDPOET5IFCMFOEFSXJMMSFUVSOUPTUBOECZNPEF
BOEUIF-$%XJMMQSPNQU13&44"/:#6550/50#-&/%
NOTE:
*GOPCVUUPOJTQSFTTFEGPSTFDPOETXIFOQSPNQUFEUP"%%
/&8130(3".UIFCMFOEFSXJMMFYJUOFXQSPHSBNNJOHNPEFBOEXJMM
return to standby mode. The new program will not be stored.
5PSVOOFXQSPHSBNTTJNQMZQSFTTUIFEFTJSFE1SPHSBNCVUUPOBOEUIF
blender will run the program set by the user. The LCD will display NEW
130(3".BOEXJMMDPVOUEPXOUIFTFUUJNF
www.
GlobalTestSupply
.com
Find Quality Products Online at:
