Waring WFP16SCD, Руководство пользователя

Страница: 6 / 35

10 11
ASSEMBLy OF CONTINUOUS-FEED CHUTE PARTS
• Clean and sanitize the motor base, and wash, rinse, and sanitize
the continuous-feed chute, cover, slinger disc, food pusher,
food pusher insert and processing tools prior to initial use.
• Place the base on a counter or table near a 3-prong electrical
outlet. Position it so that you are looking at the front of the
unit and can see the control panel. Be certain that the cord
is unplugged. Do not plug in the cord until the processor is
completely assembled.
• Pick up the continuous-feed chute, holding it in both hands with
the chute pointing in the 4-o’clock position and the handle at
the 10-o’clock position. Place the chute on the base, fitting its
center opening over the motor shaft.
• Press the chute down so the round lower rim of the chute fits
around the circular platform. Rotate counterclockwise until it
clicks into place and engages the rear interlock.
• Place the slinger (or ejector disc) in the bowl, sliding it over the
metal motor shaft until it reaches the bottom of the chute.
• Select the appropriate accessory disc.
Follow directions on
page 9 to attach stem to disc.
• Place the cover on top of the chute with cover locking tab at
left of locking tab on chute. Press down and rotate the cover
until it latches to the tab on the continuous-feed chute. This will
prevent the lid from rising up during processing.
• The interlock tab on the cover will slide into the interlock slot on
the cover and engage the magnetic safety interlock switch. The
interlock switch prevents operation of the machine unless the
cover is in the proper position. With this switch engaged, the
food processor will operate if the power is on and the controls
are turned to ON or PULSE.
• To assemble the dicing assembly (WFP16S13) you may use only
the continuous feed. Do not attempt to use the dicing grid in
the batch bowl. First remove the continuous-feed chute cover
and be sure that the slinger is properly installed (see above for
assembly of continuous-feed chute). Position the dicing grid so
that it fits securely on the tabs of the continuous feed chute.
Guide the stem of the slicing blade through the center hole of
the dicing grid and over the drive shaft. Be sure that the slicing
disc is completely secured on the shaft by spinning the disc
lightly until it is almost flush with the dicing grid. Do not turn on
DISASSEMBLy OF BATCH BOWL PARTS
ALWAyS UNPLUG THE UNIT BEFORE DISASSEMBLING.
• Remove the large food pusher from the feed tube. Remove the
small pusher from the large pusher.
Disassembly when removing the S-blade or whipping
disc
• Remove the work bowl from the unit by rotating clockwise
(left) to disengage the tabs on the bottom of the bowl platform
from the work bowl. When the bowl handle is on the left
(about 7 o’clock position), you can gently lift the bowl straight
up and out.
It is recommended that you remove the bowl from the motor
base before you remove the S-blade or whipping disc.
NOTE: REMOVE ALL FOOD AND LIqUID BEFORE REMOVING
S-BLADE OR WHIPPING DISC, OR BOWL WILL LEAK.
• To remove the blade or disc, keep a slight downward pressure
on the top center hub of the blade or disc while removing the
bowl from the motor base. This will form a seal to prevent food
particles from spilling into the center tube of the bowl and onto
the motor base or the work surface. Remove all contents from
the batch bowl. Then remove the S-blade or whipping disc
from the bowl by pulling upward to unlock the seal. Handle the
S-blade with caution; the blades are extremely sharp.
Disassembly when removing an accessory disc
• Do not remove the work bowl until the accessory disc is
removed.
• To remove an accessory disc, place your fingers on the outer
edge of two opposite sides of the disc and lift. The disc should
remove easily off the disc stem. If the disc stem stays attached
to the disc, hold the disc in one hand with the stem facing away
from your hand and pull out the disc stem. Be careful not to
scrape your hand on any sharp edges.
• Remove the work bowl from the unit by rotating clockwise (left)
to disengage the tabs on the bottom of the bowl platform
from the work bowl. When the bowl handle is on the left (about
7 o’clock position), you can gently lift the bowl straight up and out.