Waring WFP16SCD, Руководство пользователя

Страница: 5 / 35

8 9
ASSEMBLy OF BATCH BOWL PARTS
We will use the terms work bowl, batch bowl and cutter bowl
interchangeably throughout this instruction book. They mean the
same thing.
Prior to First Use:
• Clean and sanitize the motor base. Wash, rinse, and sanitize
the work bowl, cover, food pusher, food pusher insert and
accessories.
• Place base on a counter or table near a 3-prong electrical
outlet. Position it so you look at the front of the unit and can see
the control panel. Do not plug in the cord until the processor is
completely assembled.
• Pick up the transparent work bowl, holding it in both hands with
the handle toward you.
• Place the bowl on the base, fitting its central tube over the
motor shaft on the base and placing its handle slightly to the
left of back-center (at about a 7 o’clock position).
• Press the bowl down so the lower rim fits around the circular
platform. Turn the bowl counterclockwise as far as it will go. It
will lock into position with the tabs on the sides of the
platform.
Read this if assembling the batch bowl parts to use S-blade
(cutter blade) or whipping disc.
• Pick up the S-blade or whipping disc, noting the diagram on
the top of the plastic center. It matches the shape of the motor
shaft.
• Place the S-blade or whipping disc over the tip of the motor
shaft, lining up the inside of the hub with the shaft. Press it
down firmly, rotating the center hub until the blade or disc
assembly is fully seated. It should easily drop into place. Push
firmly to lock and seal S-blade or whipping disc hub in place.
Be sure it is pushed down as far as it will go. If it is not all the
way down, it may become damaged and any liquid may leak.
Push only on the center section (plastic part); never touch the
cutting blade, as it is extremely sharp.
• Check to be sure the blade or disc is all the way down by
turning it back and forth while gently pushing it down. If
properly installed and fully seated, the lower blade will be
positioned just above the inside bottom of the bowl.
• If processing food with the S-blade or whipping disc, now is the
time to add the food or liquid to the work bowl.
• Do not fill liquid over MAx LIqUID FILL LINE . If too much
liquid is used, it will overflow. In this case, stop operation,
remove liquid to below MAx LIqUID FILL LINE and continue
processing.
Read this if assembling batch bowl parts to use accessory
discs in batch bowl.
To assemble the adjustable slicing disc (WFP16S10), you must
remove bowl cover. Position the disc stem over the drive shaft
securely. Next, select the desired thickness setting on your
adjustable slicing disc. There are 16 different positions ranging
from 1–6mm in thickness. Once you’ve set the thickness, position
the plastic receptacle over the disc stem securely. Do not turn on
the unit until the batch bowl is properly assembled with the cover.
To assemble the reversible shredding disc (WFP16S12), you must
remove bowl cover. Position the disc stem over the drive shaft
securely. Next, select the desired shredding blade size. Your
reversible shredding disc has fine shredding blades on one side
and medium shredding blades on the other. Be sure the desired
blade size is facing up, and position the disc on the disc stem
securely. Do not turn on the unit until the batch bowl is properly
assembled with the cover.
NEVER ATTEMPT TO START THE FOOD PROCESSOR
WITHOUT THE COVER LOCKED INTO POSITION.
Two pushers for feed tube
There is a large food pusher and small food pusher. The large
pusher is for processing larger foods. The small pusher nests in
the large pusher and can be used for smaller products, guiding
long thin vegetables for more precise cuts, or for jobs like slicing
pepperoni. Insert the small food pusher into the large food pusher
opening. Now you are ready to insert the large pusher into the
feed tube opening.