background image

3.8 Operating Lift Table: 

Up and down buttons are located on the top of the control handle. To 

raise the platform push and hold “UP” button until it reaches the required height (max height 
1000mm). To lower the platform push and hold the down button. 

 
Warning: 

Before you operate, practice in a open area for 

at least one hour

 to get familiar with the 

Trolley

 

and gain the operation skills. The brake may not be effective when engaged on inclines greater 
than the grade with allowed load. Be alert! 
 

Emergency Stop 

 
In case of out-of-control, turn the power off immediately! 
 
4. SAFETY INSTRUCTIONS 

We disclaim all responsibility for any personal injury or property damage, which may occur as a 
result of improper or unsafe use of its products. The following guidelines are intended to assist 
you in the safe operation of your 

Trolley.

 Should you have any questions about the correct 

operation of your 

Trolley,

 please contact dealer. 

 
Your 

Trolley

, can negotiate grass, gravel, dirt and sand surfaces, as well as hard paved or carpeted 

surfaces. However, extra caution should be taken when operating your unit on uneven surfaces 
other than flat surfaces. 
 
There are some concerns about electromagnetic interference to powered equipment. You need to 
know what EMI (Electromagnetic Interference) is and how to prevent such incidents. The 
following paragraphs are intended to provide you some important information about this. 
 

CAUTION: 

 

 
IT IS VERY IMPORTANT THAT YOU READ THIS INFORMATION REGARDING THE 
POSSIBLE EFFECTS OF ELECTOMAGNETIC INTERFERENCE ON YOUR 
POWERED EQUIPMENT. 
 
Electromagnetic Interference (EMI)

 

 

 

Electrically powered equipment may be susceptible to Electromagnetic Interference (EMI). 
Sources such as Radio Stations, TV Stations, Amateur Radio Transmitters, Two Way Radios and 
Cellular Phones all emit electromagnetic energy (EM). It is highly unlikely but in extreme cases 
where the intensity of EM is very high it may cause the powered equipment to release its brakes 
or move by itself. Powered equipment has a certain immunity level which in most cases is 
adequate. If you feel EMI may be a risk then you should conduct a site specific test and risk 
assessment to ensure the EM is within the products immunity level.   
If you notice any unintentional movement or brake release we recommend turning the unit off 
immediately taking note of any high powered communications device in the area.  
 
 

Содержание P2GOARROWMATEHD
















Отзывы: