warema_816830_alhb_en_v4•2022-10-01
We reserve the right to make technical modifications
2
Remove the terminal covers:
Insert a suitable screwdriver
into the notch!
Fig. 2 Removing the terminal covers (REG variant)
■
The motor control unit is electrically connected ac-
cording to the wiring diagram on the back of this
Commissioning
After installation has been completed and the supply volt-
age has been connected, the sun shading system can be
operated on-site via the connected push button or the op-
tionally available manual operating unit MABE 12. The fol-
lowing table informs you on which sun shading drives can
be controlled using the connected sunblind push buttons
(factory setting, can be changed later):
Sunblind push button
at input
Controls motor
1 (E3.1 / E3.2)
1
2 (E4.1 / E4.2)
2
3 (E5.1 / E5.2)
3
4 (E6.1 / E6.2)
4, 5, 6
However, to centrally operate the system and set up the
convenience and safety functions, the LonWorks network
must be put into operation. This is described in the soft-
ware documentation of your control unit. Contact your sys-
tem integrator in this matter.
Service button and status LEDs:
The LONMSE printed
circuit board has a red and a green status LED and a ser-
vice button (see Fig. 3). Perform a simple function test: Af-
ter the supply voltage is switched on or after briefly press-
ing the service button, the green LED lights up for approx.
0.5 seconds and then goes out. If the LED lights up con-
tinuously, this indicates a device fault. In this case, contact
your system integrator. After the supply voltage is switched
on, the red LED lights up for up to 20 seconds. As soon as
the device is ready for operation, this LED begins flashing
irregularly. If it lights up continuously, this indicates a de-
vice fault. In this case, contact your system integrator.
I Take suitable precautions to prevent damage due
to electrostatic discharge!
001358799800 LONMSE6
001358799800 LONMSE6
F1
F1
Pull off the bar code
label
E
3.2
E
3.1
1 2 3 4 5 6 7 8 9
X5
P
E
2.2
P
E
2.1
E
1.2
E
1.1 P
St1
001358799800 LONMSE6
001358799800 LONMSE6
Fig. 3 LONMSE 6M230I AP (top) or REG (bottom)
Function of the LONMSE 6M230I
Convenience and safety functions
These functions have been integrated in your software and
customized according to your wishes. A detailed descrip-
tion can be found in the software documentation of your
sun shading control system.
Local operation
By briefly pressing the sunblind push button
(< 0.6 sec-
onds),
you can adjust the sun shading system
in small
steps.
If the push button is pressed for
between 0.6 and
2.6 seconds
, a move command is triggered and the
sun shading system moves roughly for as long as you
keep the button pressed.
If the push button is pressed for
longer than 2.6 sec-
onds
, the sun shading system moves to the upper or
lower limit position. To stop the motion, briefly press the
button for the direction opposite to the direction of the
move command.
Maintenance
There are no parts inside the device that require
maintenance. In the event of a malfunction, the built-
in miniature fuses may only be replaced by a certified
electrician.
Cleaning
Clean the housing with a soft, dry cloth. Do not use
detergents, cleaning agents, solvents, abrasive substances
or steam cleaners!
Liability
Failure to comply with the product information in these
instructions and any use of the device other than its
intended use may result in the manufacturer refusing to
honour warranty claims for product damage. In this case,
liability for secondary harm to persons or damage to
property will also be excluded. Observe the information in
the operating instructions for your sun shading system. The
automatic or manual operation of the sun shading system
while iced over and the use of the sun shading system
during severe weather may cause damage and must be
prevented by the operator through suitable precautions.
Obligations for the disposal of electrical
devices
A marking with this symbol indicates the following
obligations under the scope of legal regulations:
The owner of this electrical device must dispose of it
separately from unsorted municipal waste for further
recycling.
Used batteries and accumulators that are not enclosed
in the old device, as well as lamps/bulbs that can be
removed from the old device without breaking, must be
disposed of separately.
Distributors of electrical devices and disposal companies
are obliged to take back the equipment free of charge.
The owner must take it upon themselves to delete any
personal data contained in the electrical device prior to
disposal.
