W&T 58620 Скачать руководство пользователя

Страница: 55 / 89

W&T

Modem Operation

Subject to error and alteration

5.4.13 &D (AT&C[0|1|2|3])

Modem response to DTR option

Default setting: 2

Defines the effect of a level change on the DTR input on the
LAN-Modem. One of four functions may be selected:

•

&D0

The LAN-Modem ignores the signal.

•

&D1

If the LAN-Modem is in data mode,k an ON

OFF change

places the modem in command mode. The ATO command
can be used to return to data mode.

•

&D2

A change from ON

OFF breaks the existing connection.

A new connection can only be established when an enable
level is present on DTR.

•

&D3

Has the same function as

&D2

but additionally it resets the

LAN-Modem. If the LAN-Modem is on data mode, a level
change on the DTR input is only recognized if it is present
for the time defined in S-register

Содержание 58620


























































































Результаты поиска

Содержание 58620

Отзывы:

Похожие инструкции для 58620

Бренды по названию

Популярные бренды

W&T 58620, Руководство пользователя

Результаты поиска

Содержание 58620

Отзывы:

Похожие инструкции для 58620

Бренды по названию

Популярные бренды