W&H Lara RIL-117 Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 138

background image

Diagnostic

108

LARA | Instructions for use | RIL-1 ENG Rev04 | 28/02/2019 | © 2019 W&H Sterilization Srl

TROUBLESHOOTING TABLE

Notice: Before sending the sterilizer for technical service, remove the mains cable, empty both water tanks and use the original or appropriate
packaging.

Problem

Possible cause

Solutions

The sterilizer remains switched
OFF.

The mains switch or network circuit breaker is OFF.

Activate the mains switch or network circuit breaker (ON).

No voltage at the socket.

Check the electric circuit.

The power cord is not connected properly.

Check and connect the power cord properly.

Water is leaking at the front of the
sterilizer.

Leaks through the chamber door seal.

Clean or replace the door seal.

Clean the chamber face side.

Internal leak.

Call technical service.

The cycle commences but there is
no pressure/temperature rise.

The thermal overload switch is open.

Reset the thermal overload switch. See "Extraordinary maintenance" on page 92.

Electric - electronic fault.

Call technical service.

At the end of the cycle, there is
residual water in the chamber.

Sterilizer not properly leveled.

Properly level the surface the sterilizer is placed on.

Overloaded chamber.

Comply with the maximum load weight limits for each type of load. Always use the
chamber rack for trays and cassettes. See ."Load maintenance and preparation" on
page 54

Chamber filter clogged.

Remove and clean the chamber filter.

Chamber filter cap not well-positioned.

Mount the chamber filter cap properly (see "Ordinary maintenance" on page 73)

Load incorrectly placed.

See "Load maintenance and preparation" on page 54

«
...
106
107
108
109
110
...
»

Содержание Lara RIL-117











































































































































Отзывы:

Нет отзывов

Похожие инструкции для Lara RIL-117

Бренд: Vivog Страницы: 2

Бренд: hatch Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды